- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1041 (Analog Devices, Inc.) Secondary-Side Controller with Current Share and Housekeeping PDF資料下載
參數資料
| 型號： | ADM1041 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Secondary-Side Controller with Current Share and Housekeeping |
| 中文描述： | 二次側電流控制器共享和管家 |
| 文件頁數： | 52/64頁 |
| 文件大小： | 1063K |
| 代理商： | ADM1041 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
ADM1041
MICROPROCESSOR SUPPORT
Table 43.
Mnemonic
Description
m_pson_r
Allows the microprocessor to read the state of PSON. This allows only one
ADM1041 to be configured as the PSON interface to the host system.
m_pson_w
Allow the microprocessor to write to control the PSON function of each ASIC.
When in microprocessor support mode, the principle configuration for controlling
power-on/power-off will be as follows: One ADM1041 would be configured to be
the interface to the host system through the standard PSON pin. This pin would be
configured not to write through to the PSON debounce block. The microprocessor
would poll the status of this ADM1041 by reading m_pson_r. Debouncing would
be done by the microprocessor. If m_pson_r changed state, the microprocessor
would write the new state to m_pson_w in all ADM1041s on the SMBus. If a fault
were to occur on any output, the SMBAlert interrupt would request microprocessor
attention. If this means turning all ADM1041s off, this would be done by writing a
zero to the m_pson_w bit.
m_acsns_r
Allows the microprocessor to read the state of AC
SENSE
1/AC
SENSE
2. This allows one
ADM1041 to be configured as the interface to the host power supply.
m_acsns_w
Allow the microprocessor to write to control the ACSOK function of each ADM1041.
When in microprocessor support mode the principle configuration for controlling
AC_OK, undervoltage blanking, PEN gating, and RAMP/SS gating will be as follows:
One ADM1041 will be configured to be the interface with the host power supply
AC monitoring circuitry. This ADM1041 might be configured so that the acsns
signal would be written through or would not be written through. Regardless, the
microprocessor would monitor m_acsns_r and write to m_acsns_w as appropriate.
Since it is possible to sense but not to write through, it is possible to configure a
second ADM1041 to monitor a second ac or bulk voltage.
m_shr_clmp
Allow the μP to write directly to m_shr_clmp to control when the ISHARE clamp is
released. During a hot-swap insertion, there may be a need to delay the release of
the ISHARE clamp. This allows the designer an option over the default release at
75% or 88% of the reference ramp (soft-start).
m_cbd_w
Allow the microprocessor to write directly to CBD as a possible way of adding an
additional output port. This might be for blinking LEDs or as a FAIL signal to the
system.
m_cbd_clr
Allows the microprocessor to clear the CBD latch following an SMBalert. If CBD is
configured to be latching, there may be circumstances that lead to CBD/SMBAlert
being set by, for example, one of the MON flags but does not lead to PSON being
cycled and CBD being reset. In this case, the microprocessor needs to write directly
to CBD to reset the latch.
mfg5
This flag indicates the status of the MON5 pin.
mfg4
This flag indicates the status of the MON4 pin.
mfg3
This flag indicates the status of the MON3 pin.
mfg2
This flag indicates the status of the MON2 pin.
mfg1
This flag indicates the status of the MON1 pin.
ocpto
If this flag is high, an overcurrent has occurred and timed out.
uvfault
If this flag is high, an undervoltage has been sensed
ovfault
If this flag is high, an overvoltage has been sensed.
vddov
If this flag is high, a V
DD
overvoltage has been sensed.
extrefok
If this flag is low, the externally available reference on Pin 18 is overloaded.
intrefok
If this flag is low, the internal reference has no integrity.
gndok
If this flag is low, the ASIC ground, Pin 7, is open either pin to PCB or bond wires.
V
DD
OK
If this flag is low, V
DD
is below its UVL or the power mangement block has a
problem, a reference voltage, ground fault, or V
DD
overvoltage fault.
reverseok
If this flag is low, the OrFET has an excessive reverse voltage.
orfetok
If this flag is low, either PULSE_OK, penok, loadvok, or reverseok is false.
Share_OK
If this flag is low, the current share accuracy is out of limits.
fault
Fault latch. If this flag is high, either an ovfault, uvfault, or ocp has occured.
PULSE_OK
Pulses are present at AC
SENSE
1.
Rev. A | Page 52 of 64
Register
02h
Bit
6
Read/Write
Read-only
12h
1
Write-only
02h
7
Read-only
12h
5
Write-only
13h
2
Write-only
1Bh
1
Write-only
13h
0
Write-only
00h
00h
00h
00h
00h
00h
00h
00h
01h
01h
01h
01h
01h
0
1
2
3
4
5
6
7
0
1
2
3
4
Read-only
Read-only
Read-only
Read-only
Read-only
Read-only
Read-only
Read-only
read only
Read-only
Read-only
Read-only
Read-only
01h
01h
01h
02h
02h
5
6
7
0
1
Read-only
Read-only
Read-only
Read-only
Read-only
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1041A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041AARQZ-REEL | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041AARQZ-REEL7 | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓?fù)浣Y(jié)構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
發布緊急采購，3分鐘左右您將得到回復。