- 您現在的位置：買賣IC網 > PDF目錄223310 > ADM1028ARQZ-REEL7 (ANALOG DEVICES INC) SPECIALTY ANALOG CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | ADM1028ARQZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | MO-137AB, QSOP-16 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 379K |
| 代理商： | ADM1028ARQZ-REEL7 |
REV. B
ADM1028
–8–
TEMPERATURE MEASUREMENT SYSTEM
Internal Temperature Measurement
The ADM1028 contains an on-chip bandgap temperature sen-
sor. The on-chip ADC performs conversions on the output of
this sensor and outputs the temperature data in 8-bit two’s
complement format. The format of the temperature data is
shown in Table I.
Table I. Temperature Data Format
Temperature
Digital Output
–128
∞C
1000 0000
–125
∞C
1000 0011
–100
∞C
1001 1100
–75
∞C
1011 0101
–50
∞C
1100 1110
–25
∞C
1110 0111
–1
∞C
1111 1111
0
∞C
0000 0000
+1
∞C
0000 0001
+10
∞C
0000 1010
+25
∞C
0001 1001
+50
∞C
0011 0010
+75
∞C
0100 1011
+100
∞C
0110 0100
+125
∞C
0111 1101
+127
∞C
0111 1111
External Temperature Measurement
The ADM1028 can measure the temperature of an external
diode sensor or diode-connected transistor, connected to Pins 9
and 10.
Pins 9 and 10 are a dedicated temperature input channel. The
default functions of Pins 11 and 12 are as
THERM outputs to
indicate over-temperature conditions.
The forward voltage of a diode or diode-connected transistor,
operated at a constant current, exhibits a negative temperature
coefficient of about –2 mV/
∞C. Unfortunately, the absolute value
of VBE varies from device to device, and individual calibration
is required to null this out, making the technique unsuitable
for mass production.
The technique used in the ADM1028 is to measure the change
in VBE when the device is operated at two different currents.
This is given by:
DVBE = KT/q ln(N)
where:
K is Boltzmann’s constant.
q is charge on the carrier.
T is absolute temperature in Kelvins.
N is ratio of the two currents.
Figure 3 shows the input signal conditioning used to measure
the output of an external temperature sensor. This figure shows
the external sensor as a substrate transistor, provided for tempera-
ture monitoring on some microprocessors, but it could equally
well be a discrete transistor.
If a discrete transistor is used, the collector will not be grounded,
and should be linked to the base. If a PNP transistor is used, the
base is connected to the D– input and the emitter to the D+
input. If an NPN transistor is used, the emitter is connected to
the D– input and the base to the D+ input.
To prevent ground noise interfering with the measurement, the
more negative terminal of the sensor is not referenced to ground,
but is biased above ground by an internal diode at the D– input.
If the sensor is used in a very noisy environment, a capacitor of
value up to 1000 pF may be placed between the D+ and D–
inputs to filter the noise.
To measure
DVBE, the sensor is switched between operating
currents of I and N
I. The resulting waveform is passed
through a 65 kHz low-pass filter to remove noise, thence to a
chopper-stabilized amplifier that performs the functions of
amplification and rectification of the waveform to produce a dc
voltage proportional to
DVBE. This voltage is measured by the
ADC to give a temperature output in 8-bit two’s complement
format. To further reduce the effects of noise, digital filtering is
performed by averaging the results of 16 measurement cycles.
An external temperature measurement nominally takes 9.6 ms.
LOW-PASS
FILTER
fC = 65kHz
BIAS
DIODE
REMOTE
SENSING
TRANSISTOR
IN
IIBIAS
D+
D–
VOUT+
VOUT–
TO
ADC
VDD
Figure 3. Signal Conditioning
LAYOUT CONSIDERATIONS
Digital boards can be electrically noisy environments, and care
must be taken to protect the analog inputs from noise, particu-
larly when measuring the very small voltages from a remote
diode sensor. The following precautions should be taken:
1. Place the ADM1028 as close as possible to the remote sens-
ing diode. Provided that the worst noise sources such as clock
generators, data/address buses and CRTs are avoided, this
distance can be 4 to 8 inches.
2. Route the D+ and D– tracks close together, in parallel with
grounded guard tracks on each side. Provide a ground plane
under the tracks if possible.
3. Use wide tracks to minimize inductance and reduce noise
pickup. Ten mil track minimum width and spacing is rec-
ommended.
4. Try to minimize the number of copper/solder joints, which
can cause thermocouple effects. Where copper/solder joints
are used, make sure that they are in both the D+ and D–
path and at the same temperature.
Thermocouple effects should not be a major problem as 1
∞C
corresponds to about 200
mV, and thermocouple voltages are
about 3
mV/oC of temperature difference. Unless there are
two thermocouples with a big temperature differential between
them, thermocouple voltages should be much less than 200
mV.
5. Place 0.1
mF bypass and 2200 pF input filter capacitors close
to the ADM1028.
6. If the distance to the remote sensor is more than 8 inches, the
use of twisted-pair cable is recommended. This will work up
to about 6 to 12 feet.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1232ARWZ | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| ADM2223AL5 | FIBER OPTIC ADD/DROP MUX/DEMUX, FC/SPC CONNECTOR |
| ADM322323BB4 | FIBER OPTIC ADD/DROP MUX/DEMUX, SC/APC CONNECTOR |
| ADM322323AL5 | FIBER OPTIC ADD/DROP MUX/DEMUX, FC/SPC CONNECTOR |
| ADP-ED7887/1+ | 1 MHz - 1050 MHz RF/MICROWAVE COMBINER, 3.94 dB INSERTION LOSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1029 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PWM Fan Controller and Temperature Monitor for High Availability Systems |
| ADM1029ARQ | 制造商:Rochester Electronics LLC 功能描述:TDM AND FAN CONTROLLER I.C. - Bulk |
| ADM1029ARQ-REEL7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1029ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 +/- 1 C Digital Serial RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1029ARQZ-R7 | 功能描述:馬達/運動/點火控制器和驅動器 +/- 1 C Digital Serial RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。