參數資料
型號： ADM1026JSTZ-REEL
廠商： ANALOG DEVICES INC
元件分類： 電源管理
英文描述： Complete Thermal and System Management Controller
中文描述： 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48
封裝： 7 X 7 MM, 1.40 MM HEIGHT, LEAD FREE, PLASTIC, MS-026BBC, LQFP-48
文件頁數： 28/56頁
文件大?。?/td> 634K
代理商： ADM1026JSTZ-REEL
ADM1026
ADM1026 Interrupt Structure
The Interrupt Structure of the ADM1026 is shown in Figure 53.
Interrupts can come from a number of sources, which are com-
bined to form a common INT output. When INT is asserted,
this output pulls low. The INT pin has an internal, 100 k
pull-up resistor.
Rev. A | Page 28 of 56
Analog/Temperature Inputs
As each analog measurement value is obtained and stored in the
appropriate value register, the value and the limits from the
corresponding limit registers are fed to the high and low limit
comparators. The device performs greater than comparisons to
the high limits. An out-of-limit is also generated if a result is
less than or equal to a low limit. The result of each comparison
(1 = out of limit, 0 = in limit) is routed to the corresponding
bit input of Interrupt Status Register 1, 2, or 4 via a data
demultiplexer, and used to set that bit high or low as appro-
priate. Status bits are self-clearing. If a bit in a status register is
set due to an out-of-limit measurement, it continues to cause
INT to be asserted as long as it remains set, as described later.
However, if a subsequent measurement is in limit, it is reset and
does not cause INT to be reasserted. Status bits are unaffected
by clearing the interrupt.
Interrupt Mask Registers 1, 2, and 4 have bits corresponding to
each of the interrupt status register bits. Setting an interrupt
mask bit high conceals an asserted status bit from display on
Interrupt Pin 17. Setting an interrupt mask bit low allows the
corresponding status bit to be asserted and displayed on Pin 17.
After mask gating, the status bits are all OR’ed together to
produce the analog and fan interrupt that is used to set a latch.
The output of this latch is OR’ed with other interrupt sources to
produce the INT output. This pulls low if any unmasked status
bit goes high, that is, when any measured value goes out of limit.
When an INT output caused by an out-of-limit analog/
temperature measurement is cleared by one of the methods
described later, the latch is reset. It is not set again, and INT is
not reasserted until after two local temperature measure-ments
have been taken, even if the status bit remains set or a new
analog/temperature event occurs, as shown in Figure 50. This
delay corresponds to almost two monitoring cycles, and is about
530 ms. However, interrupts from other sources such as a fan or
GPIO can still occur. This is illustrated in Figure 51.
START OF ANALOG
MONITORING
CYCLE
OUT-OF-LIMIT
MEASUREMENT
START OF ANALOG
MONITORING
CYCLE
INT
INT CLEARED
LOCAL
TEMPERATURE
MEASUREMENT
START OF ANALOG
MONITORING
CYCLE
INT RE-ASSERTED
OUT-OF-LIMIT
MEASUREMENT
FULL MONITORING CYCLE = 273ms
MEASUREMENT
TEMPERATURE
0
Figure 50. Delay After Clearing INT Before Reassertion
START OF ANALOG
MONITORING CYCLE
OUT-OF-LIMIT
MEASUREMENT
LOCAL TEMPEREATURE
MEASUREMENT
START OF ANALOG
MONITORING CYCLE
LOCAL TEMPERATURE
MEASUREMENT
START OF ANALOG
MONITORING CYCLE
INT
CLEARED
INT RE-ASSERTED
NEW INT
FROM FAN
NEW
INT
FROM GPIO
GPIO DE-ASSERTED
INT
INT
CLEARED
0
Figure 51. Other Interrupt Sources Can Reassert INT Immediately
相關PDF資料
PDF描述
ADM1026JST Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28
ADM1030ARQ Intelligent Temperature Monitor and PWM Fan Controller
ADM1030 Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35
ADM1033 Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQ Thermal Monitor and Fan Speed (RPM) Controller
相關代理商/技術參數
參數描述
ADM1026JSTZ-REEL7 制造商:Analog Devices 功能描述:IC SYSTEM MONITOR 制造商:ON Semiconductor 功能描述:IC SYSTEM MONITOR
ADM1027 制造商:AD 制造商全稱:Analog Devices 功能描述:dBCOOL-TM Remote Thermal Controller and Voltage Monitor
ADM1027ARQ 功能描述:IC THER CTRL VOLT/MONITOR 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1027ARQ-REEL 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1027ARQ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*