- 您現在的位置：買賣IC網 > PDF目錄11720 > ADM1024ARU-REEL (ON Semiconductor)IC MONITOR SYS TEMP/VOLT 24TSSOP PDF資料下載
參數資料
| 型號： | ADM1024ARU-REEL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 16/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MONITOR SYS TEMP/VOLT 24TSSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 21/Jan/2010 |
| 標準包裝： | 2,500 |
| 應用： | PC，PDA |
| 接口： | 串行 |
| 電源電壓： | 2.8 V ~ 5.5 V |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
ADM1024
http://onsemi.com
23
Using the Configuration Registers
Control of the ADM1024 is provided through two
configuration registers. The ADC is stopped upon powerup,
and the INT_Clear signal is asserted, clearing the INT output.
The Configuration Registers are used to start and stop the
ADM1024; enable or disable interrupt outputs and modes,
and provide the initialization function described above.
Bit 0 of Configuration Register 1 controls the monitoring
loop of the ADM1024. Setting Bit 0 low stops the
monitoring loop and puts the ADM1024 into a low power
mode thereby reducing power consumption. Serial bus
communication is still possible with any register in the
ADM1024 while in low power mode. Setting Bit 0 high
starts the monitoring loop.
Bit 1 of Configuration Register 1 enables or disables the
INT Interrupt output. Setting Bit 1 high enables the INT
output; setting Bit 1 low disables the output.
Bit 2 of Configuration Register 1 enables or disables the
THERM output. Setting Bit 1 high enables the INT output;
setting Bit 1 low disables the output.
Bit 3 of Configuration Register 1 is used to clear the INT
interrupt output when set high. The ADM1024 monitoring
function will stop until Bit 3 is set low. Interrupt Status
register contents will not be affected.
Bit 4 of Configuration Register 1 causes a low going 45 ms
(typ) pulse at the RESET pin (Pin 12).
Bit 6 of Configuration Register 1 is used to clear an
interrupt at the THERM output when it is set to 1.
Bit 7 of Configuration Register 1 is used to start a
Configuration Register Initialization when it is set to 1.
Bit 0 of Configuration Register 2 is used to mask
temperature interrupts at the INT output when it is set to 1.
The THERM output is unaffected by this bit.
Bits 1 and 2 of Configuration Register 2 lock the values
stored in the Local and Remote Fan Control Registers at
addresses 13h and 14h. The values in these registers cannot
be changed until a power-on reset is performed.
Bit 3 of Configuration Register 2 selects the THERM
interrupt mode. The default value of 0 selects onetime
mode. Setting this bit to 1 selects ACPI mode.
Starting Conversion
The monitoring function (analog inputs, temperature, and
fan speeds) in the ADM1024 is started by writing to
Configuration Register 1 and setting Start (Bit 0) high. The
INT_Enable (Bit 1) should be set to 1, and INT Clear (Bit 3)
set to 0 to enable interrupts. The THERMenable bit (Bit 2)
should be set to 1 and the THERM Clear bit (Bit 6) should
be set to 0 to enable temperature interrupts at the THERM
pin. Apart from initially starting together, the analog
measurements and fan speed measurements proceed
independently, and are not synchronized in any way.
The time taken to complete the analog measurements
depends on how they are configured, as described
elsewhere. The time taken to complete the fan speed
measurements depends on the fan speed and the number of
tachometer output pulses per revolution.
Once the measurements have been completed, the results
can be read from the Value Registers at any time.
Reduced Power and Shutdown Mode
The ADM1024 can be placed in a low power mode by
setting Bit 0 of the Configuration Register to 0. This disables
the internal ADC. Full shutdown mode may then be
achieved by setting Bit 0 of the Test Register to 1. This turns
off the analog output and stops the monitoring cycle, if
running, but does not affect the condition of any of the
registers. The device will return to its previous state when
this bit is reset to 0.
Application Circuit
Figure 37 shows a generic application circuit using the
ADM1024. The analog monitoring inputs are connected to
the power supplies including two processor core voltage
inputs. The VID inputs are connected to the processor
voltage ID pins. There are two tachometer inputs from fans,
and the analog output is used to control the speed of a third
fan. An opto-sensor for chassis intrusion detection is
connected to the CI input. Of course, in an actual
application, every input and output may not be used, in
which case unused analog and digital inputs should be tied
to analog or digital ground as appropriate.
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26FE99PA | CONN PLUG 23POS STRAIGHT W/PINS |
| ADUC843BSZ62-3 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| D38999/26WD97SA | CONN PLUG 12POS STRAIGHT W/SCKT |
| ADUC841BCPZ8-3 | IC MCU 8KB FLASH ADC/DAC 56LFCSP |
| D38999/20JF32SN | CONN RCPT 32POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1024ARUZ | 功能描述:馬達/運動/點火控制器和驅動器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1024ARUZ-R7 | 功能描述:板上安裝溫度傳感器 +/-2 C / +/-3 C Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL | 功能描述:板上安裝溫度傳感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL7 | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024EVB | 功能描述:BOARD EVAL FOR ADM1024 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
發布緊急采購，3分鐘左右您將得到回復。