- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1024 (Analog Devices, Inc.) System Hardware Monitor with Remote Diode Thermal Sensing PDF資料下載
參數資料
| 型號： | ADM1024 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | System Hardware Monitor with Remote Diode Thermal Sensing |
| 中文描述： | 系統硬件監控與遠程二極管溫度傳感器 |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 285K |
| 代理商： | ADM1024 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADM1024
–16–
REV. 0
If the fan has a strong pull-up (less than 1 k
) to 12 V, or a
totem-pole output, then a series resistor can be added to limit the
Zener current, as shown in Figure 17c. Alternatively, a resistive
attenuator may be used, as shown in Figure 17d.
R1 and R2 should be chosen such that:
2
V
<
V
PULL-UP
×
R2/(R
PULL-UP
+
R
1 +
R
2) < 5
V
The fan inputs have an input resistance of nominally 160 k
to
ground, so this should be taken into account when calculating
resistor values.
With a pull-up voltage of 12 V and pull-up resistor less than 1 k
,
suitable values for R1 and R2 would be 100 k
and 47 k
. This
will give a high-input voltage of 3.83 V.
12V
TACHO
OUTPUT
FAN1 OR
FAN2
V
CC
FAN SPEED
COUNTER
ZD1
*
ZENER
*
CHOOSE ZD1 VOLTAGE APPROX. 0.8 V
CC
PULL-UP
TYP. <1k
OR TOTEM-POLE
R1
10k
160k
Figure 17c. Fan with Strong Tach. Pull-Up to >V
CC
or
Totem-Pole Output, Clamped with Zener and Resistor
12V
<1k
TACHO
OUTPUT
FAN1 OR
FAN2
V
CC
*
SEE TEXT
R2
*
R1
*
FAN SPEED
COUNTER
160k
Figure 17d. Fan with Strong Tach. Pull-Up to >V
CC
or
Totem-Pole Output, Attenuated with R1/R2
FAN SPEED MEASUREMENT
The fan counter does not count the fan tach output pulses directly,
because the fan speed may be less than 1000 rpm and it would
take several seconds to accumulate a reasonably large and accu-
rate count. Instead, the period of the fan revolution is measured
by gating an on-chip 22.5 kHz oscillator into the input of an 8-bit
counter for two periods of the fan tach output, as shown in Fig-
ure 18; the accumulated count is actually proportional to the fan
tach period and inversely proportional to the fan speed.
22.5kHz
CLOCK
CONFIG.
REG. 1 BIT 0
FAN1
INPUT
FAN2
INPUT
START OF
MONITORING
CYCLE
FAN1
MEASUREMENT
PERIOD
FAN2
MEASUREMENT
PERIOD
Figure 18. Fan Speed Measurement
The monitoring cycle begins when a one is written to the Start
Bit (Bit 0), and a zero to the
INT
_Clear Bit (Bit 3) of the
Configuration Register.
INT
_Enable (Bit 1) should be set to
one to enable the
INT
output. The measurement begins on the
rising edge of a fan tach pulse, and ends on the next-but-one
rising edge. The fans are monitored sequentially, so if only one
fan is monitored the monitoring time is the time taken after the
Start Bit for it to produce two complete tach cycles or for the
counter to reach full scale, whichever occurs sooner. If more
than one fan is monitored, the monitoring time depends on the
speed of the fans and the timing relationship of their tach pulses.
This is illustrated in Figure 19. Once the fan speeds have been
measured, they will be stored in the Fan Speed Value Registers
and the most recent value can be read at any time. The measure-
ments will be updated as long as the monitoring cycle continues.
To accommodate fans of different speed and/or different num-
bers of output pulses per revolution, a prescaler (divisor) of
1, 2, 4, or 8 may be added before the counter. The default value
is 2, which gives a count of 153 for a fan running at 4400 rpm
producing two output pulses per revolution.
The count is calculated by the equation:
Count
= (22.5
×
10
3
×
60) /(
rpm
×
Divisor
)
For constant speed fans, fan failure is normally considered to have
occurred when the speed drops below 70% of nominal, which
would correspond to a count of 219. Full scale (255) would be
reached if the fan speed fell to 60% of its nominal value. For
temperature-controlled variable speed fans the situation will be
different.
Table V shows the relationship between fan speed and time
per revolution at 60%, 70%, and 100% of nominal rpm for fan
speeds of 1100, 2200, 4400, and 8800 rpm, and the divisor that
would be used for each of these fans, based on two tach pulses
per revolution.
Table V. Fan Speeds and Divisors
Time
per
Time
per
Rev (70%) 60%
rpm (ms)
Time
per
Rev (60%)
(ms)
Nominal Rev
70%
Divisor rpm
(ms)
rpm
÷
1
÷
2
÷
4
÷
8
8800
4400
2200
1100
6.82
13.64
27.27
54.54
6160 9.74
3080 19.48
1540 38.96
770
5280
2640
1320
660
11.36
22.73
45.44
90.90
77.92
FAN1 and FAN2 Divisors are programmed into Bits 4 to 7 of
the VID 0–3/Fan Divisor Register.
LIMIT VALUES
Fans in general will not overspeed if run from the correct voltage,
so the failure condition of interest is underspeed due to electrical
or mechanical failure. For this reason only, low-speed limits are
programmed into the limit registers for the fans. It should be noted
that, since fan period rather than speed is being measured, a fan
failure interrupt will occur when the measurement
exceeds
the
limit value.
MONITORING CYCLE TIME
The monitoring cycle time depends on the fan speed and number
of tach output pulses per revolution. Two complete periods of the
fan tach output (three rising edges) are required for each fan
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1024ARU | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025 | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025A | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025AARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1025ARQ | Low-Cost PC Hardware Monitor ASIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1024ARU | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024ARU-REEL | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024ARUZ | 功能描述:馬達/運動/點火控制器和驅動器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1024ARUZ-R7 | 功能描述:板上安裝溫度傳感器 +/-2 C / +/-3 C Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL | 功能描述:板上安裝溫度傳感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。