- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1020AR-REEL (ANALOG DEVICES INC) Circular Connector; No. of Contacts:26; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-26 PDF資料下載
參數資料
| 型號： | ADM1020AR-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Circular Connector; No. of Contacts:26; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-26 |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 132K |
| 代理商： | ADM1020AR-REEL |
REV. 0
ADM1020
–6–
Figure 11 shows the input signal conditioning used to measure
the output of an external temperature sensor. This figure shows
the external sensor as a substrate transistor, provided for tem-
perature monitoring on some microprocessors, but it could
equally well be a discrete transistor. If a discrete transistor is
used, the collector will not be grounded, and should be linked to
the base. To prevent ground noise interfering with the measure-
ment, the more negative terminal of the sensor is not referenced
to ground, but is biased above ground by an internal diode at
the D– input. If the sensor is operating in a noisy environment,
C1 may optionally be added as a noise filter. Its value is typi-
cally 2200 pF but should be no more than 3000 pF. See the
section on Layout Considerations for more information on C1.
To measure
V
BE
, the sensor is switched between operating
currents of I and N
×
I. The resulting waveform is passed
through a 65 kHz low-pass filter to remove noise, hence to a
chopper-stabilized amplifier that performs the functions of am-
plification and rectification of the waveform to produce a dc
voltage proportional to
V
BE
. This voltage is measured by the
ADC to give a temperature output in 8-bit twos complement
format. To further reduce the effects of noise, digital filtering is
performed by averaging the results of 16 measurement cycles.
Signal conditioning and measurement of the internal tempera-
ture sensor is performed in a similar manner.
TEMPERATURE DATA FORMAT
One LSB of the ADC corresponds to 1
°
C, so the ADC can
theoretically measure from –128
°
C to +127
°
C, although the
practical lowest value is limited to –65
°
C due to device maxi-
mum ratings. The temperature data format is shown in Table I.
The results of the local and remote temperature measurements
are stored in the local and remote temperature value registers,
and are compared with limits programmed into the local and
remote high and low limit registers.
C1*
D+
D–
REMOTE
SENSING
TRANSISTOR
I
N
3
I
I
BIAS
V
DD
V
OUT+
TO ADC
V
OUT–
BIAS
DIODE
*CAPACITOR C1 IS OPTIONAL.
IT IS ONLY NECESSARY IN NOISY ENVIRONMENTS.
C1 = 2.2nF TYPICAL, 3nF MAX.
LOWPASS FILTER
f
C
= 65kHz
Figure 11. Input Signal Conditioning
Table I. Temperature Data Format
Temperature
–128
°
C
–125
°
C
–100
°
C
–75
°
C
–50
°
C
–25
°
C
–1
°
C
0
°
C
+1
°
C
+10
°
C
+25
°
C
+50
°
C
+75
°
C
+100
°
C
+125
°
C
+127
°
C
Digital Output
1 000 0000
1 000 0011
1 001 1100
1 011 0101
1 100 1110
1 110 0111
1 111 1111
0 000 0000
0 000 0001
0 000 1010
0 001 1001
0 011 0010
0 100 1011
0 110 0100
0 111 1101
0 111 1111
ADM1020 REGISTERS
The ADM1020 contains nine registers that are used to store the
results of remote and local temperature measurements, high and
low temperature limits, and to configure and control the device.
A description of these registers follows, and further details are
given in Tables II to IV. It should be noted that the ADM1020’s
registers are dual port, and have different addresses for read and
write operations. Attempting to write to a read address, or to
read from a write address, will produce an invalid result. Regis-
ter addresses above 0F are reserved for future use or used for
factory test purposes and should not be written to.
Address Pointer Register
The Address Pointer Register itself does not have, or require, an
address, as it is the register to which the first data byte of every
write operation is automatically written. This data byte is an
address pointer that sets up one of the other registers for the
second byte of the write operation, or for a subsequent read
operation.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1020AR-REEL7 | 8-Lead, Low-Cost, System Temperature Monitor |
| ADM1021A | Low-Cost Microprocessor System Temperature Monitor |
| ADM1021AARQ | Low-Cost Microprocessor System Temperature Monitor |
| ADM1021 | Low Cost Microprocessor System Temperature Monitor |
| ADM1021ARQ | Low Cost Microprocessor System Temperature Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1020AR-REEL7 | 制造商:Rochester Electronics LLC 功能描述:LOW COST THERMAL DIODE MONITOR I.C. - Tape and Reel |
| ADM1021 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost Microprocessor System Temperature Monitor |
| ADM102-11/12VDC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| ADM102-11/24VDC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| ADM102-11/48VDC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。