- 您現在的位置：買賣IC網 > PDF目錄378281 > ADC10065CIMTX (NATIONAL SEMICONDUCTOR CORP) ADC10065 10-Bit 65 MSPS 3V A/D Converter PDF資料下載
參數資料
| 型號： | ADC10065CIMTX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | ADC |
| 英文描述： | ADC10065 10-Bit 65 MSPS 3V A/D Converter |
| 中文描述： | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 17/19頁 |
| 文件大小： | 945K |
| 代理商： | ADC10065CIMTX |
Applications Information
(Continued)
TABLE 1. IRS Pin Functions
IRS Pin
V
DDA
V
SSA
Floating
Full-Scale Input
2.0V
P-P
1.5V
P-P
1.0V
P-P
1.8 OUTPUT PINS
The ADC10065 has 10 TTL/CMOS compatible Data Output
pins. The offset binary data is present at these outputs while
the DF and STBY pins are low. While the t
OD
time provides
information about output timing, a simple way to capture a
valid output is to latch the data on the rising edge of the
conversion clock. Be very careful when driving a high ca-
pacitance bus. The more capacitance the output drivers
must charge for each conversion, the more instantaneous
digital current flows through V
DDIO
and V
SSIO
. These large
charging current spikes can cause on-chip ground noise and
couple into the analog circuitry, degrading dynamic perfor-
mance.Adequate bypassing, limiting output capacitance and
careful attention to the ground plane will reduce this prob-
lem. Additionally, bus capacitance beyond the specified
10 pF/pin will cause t
to increase, making it difficult to
properly latch the ADC output data. The result could be an
apparent reduction in dynamic performance. To minimize
noise due to output switching, minimize the load currents at
the digital outputs. This can be done by connecting buffers
between the ADC outputs and any other circuitry. Only one
driven input should beADC pins, will isolate the outputs from
trace and other circuit capacitances and limit the output
currents, which could otherwise result in performance deg-
radation.
1.9 APPLICATION SCHEMATICS
The following figures show simple examples of using the
ADC10065.
Figure 5
shows a typical differentially driven
input.
Figure 6
shows a single ended application circuit.
20077949
FIGURE 5. A Simple Application Using a Differential Driving Source
A
www.national.com
17
相關PDF資料 |
PDF描述 |
|---|---|
| ADC10080CIMTX | 10-Bit, 80 MSPS, 3V, 78.6 mW A/D Converter |
| ADC10080CIMT | 10-Bit, 80 MSPS, 3V, 78.6 mW A/D Converter |
| ADC10080 | 10-Bit, 80 MSPS, 3V, 78.6 mW A/D Converter |
| ADC10154CIWM | 10-Bit Plus Sign 4 レs ADCs with 4- or 8-Channel MUX, Track/Hold and Reference |
| ADC10158CIWM | 10-Bit Plus Sign 4 レs ADCs with 4- or 8-Channel MUX, Track/Hold and Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC10065CIMTX/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC1006S055 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single 10 bits ADC, up to 55 MHz or 70 MHz |
| ADC1006S055/DB | 功能描述:數據轉換 IC 開發工具 ADC DEMO BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADC1006S055-DB | 功能描述:數據轉換 IC 開發工具 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADC1006S055H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single 10 bits ADC, up to 55 MHz or 70 MHz |
發布緊急采購，3分鐘左右您將得到回復。