- 您現在的位置：買賣IC網 > PDF目錄378279 > ADC08351 (National Semiconductor Corporation) 8-Bit, 42 MSPS, 40 mW A/D Converter PDF資料下載
參數資料
| 型號： | ADC08351 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 8-Bit, 42 MSPS, 40 mW A/D Converter |
| 中文描述： | 8位，42 MSPS的40毫瓦的A / D轉換器 |
| 文件頁數： | 10/15頁 |
| 文件大?。?/td> | 492K |
| 代理商： | ADC08351 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁
Applications Information
(Continued)
the analog supply pin should be minimized, keeping it below
200 mV
at 100 kHz. Of course, higher frequency noise on
the power supply should be even more severely limited.
No pin should ever have a voltage on it that is in excess of
the supply voltages. This can be a problem upon application
of power to a circuit. Be sure that the supplies to circuits driv-
ing the CLK, OE, analog input and reference pins do not
come up any faster than does the voltage at the ADC08351
power pins.
3.0 LAYOUT AND GROUNDING
Proper grounding and proper routing of all signals is essen-
tial to ensure accurate conversion. Separate analog and
digital ground planes that are connected beneath the
ADC08351 are required to meet data sheet limits. The ana-
log and digital grounds may be in the same layer, but should
be separated from each other and should
never
overlap
each other.
Capacitive coupling between the typically noisy digital
ground plane and the sensitive analog circuitry can lead to
poor performance that may seem impossible to isolate and
remedy. The solution is to keep the analog circuitry well
separated from the digital circuitry and from the digital
ground plane.
Generally, analog and digital lines should cross each other at
90 degrees to avoid getting digital noise into the analog path.
To maximize accuracy in video (high frequency) systems,
however, avoid crossing analog and digital lines altogether.
Furthermore, it is important to keep any clock lines isolated
from ALL other lines, including other digital lines. Even the
generally accepted 90 degree crossing should be avoided as
even a little coupling can cause problems at high frequen-
cies.
Best performance at high frequencies and at high resolution
is obtained with a straight signal path. That is, the signal path
through all components should form a straight line wherever
possible.
Be especially careful with the layout of inductors. Mutual in-
ductance can change the characteristics of the circuit in
which they are used. Inductors should not be placed side by
side, even with just a small part of their bodies beside each
other.
The analog input should be isolated from noisy signal traces
to avoid coupling of spurious signals into the input. Any ex-
ternal component (e.g., a filter capacitor) connected be-
tween the converter’s input and ground should be connected
to a very clean point in the analog ground plane.
Figure 3gives an example of a suitable layout.All analog cir-
cuitry (input amplifiers, filters, reference components, etc.)
should be placed on or over the analog ground plane. All
digital circuitry and I/O lines should be placed over the digital
ground plane.
All ground connections should have a low inductance path to
ground.
4.0 DYNAMIC PERFORMANCE
The ADC08351 is ac tested and its dynamic performance is
guaranteed. To meet the published specifications, the clock
source driving the CLK input must be free of jitter. For best
DS100895-25
FIGURE 3. Layout example showing separate analog and digital ground planes connected below the ADC08351.
A
www.national.com
10
相關PDF資料 |
PDF描述 |
|---|---|
| ADC08351CIMTC | 8-Bit, 42 MSPS, 40 mW A/D Converter |
| ADC08351CIMTCX | 8-Bit, 42 MSPS, 40 mW A/D Converter |
| ADC0841 | 8-Bit P Compatible A/D Converter |
| ADC0841BCN | 8-Bit P Compatible A/D Converter |
| ADC0841BCV | 8-Bit P Compatible A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC08351_03 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit, 42 MSPS, 40 mW A/D Converter |
| ADC08351CILQ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit, 42 MSPS, 40 mW A/D Converter |
| ADC08351CILQ/NOPB | 功能描述:IC ADC 8BIT 42MSPS 24-LLP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| ADC08351CILQX | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08351CILQX/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。