- 您現在的位置：買賣IC網 > PDF目錄378278 > ADC08200CIMT (NATIONAL SEMICONDUCTOR CORP) 8-Bit, 20 MSPS to 200 MSPS, 1.05 mW/MSPS A/D Converter PDF資料下載
參數資料
| 型號： | ADC08200CIMT |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | ADC |
| 英文描述： | 8-Bit, 20 MSPS to 200 MSPS, 1.05 mW/MSPS A/D Converter |
| 中文描述： | 1-CH 8-BIT RESISTANCE LADDER ADC, PARALLEL ACCESS, PDSO24 |
| 封裝： | PLASTIC, MO-153AD, TSSOP-24 |
| 文件頁數： | 15/19頁 |
| 文件大小： | 537K |
| 代理商： | ADC08200CIMT |
Applications Information
(Continued)
3.0 POWER SUPPLY CONSIDERATIONS
A/D converters draw sufficient transient current to corrupt
their own power supplies if not adequately bypassed. A
10 μF tantalum or aluminum electrolytic capacitor should be
placed within an inch (2.5 cm) of the A/D power pins, with a
0.1 μF ceramic chip capacitor placed within one centimeter
of the converter’s power supply pins. Leadless chip capaci-
tors are preferred because they have low lead inductance.
While a single voltage source is recommended for the V
A
and V
supplies of the ADC08200, these supply pins
should be well isolated from each other to prevent any digital
noise from being coupled into the analog portions of the
ADC. A choke or 27
resistor is recommended between
these supply lines with adequate bypass capacitors close to
the supply pins.
As is the case with all high speed converters, the ADC08200
should be assumed to have little power supply rejection.
None of the supplies for the converter should be the supply
that is used for other digital circuitry in any system with a lot
of digital power being consumed. The ADC supplies should
be the same supply used for other analog circuitry.
No pin should ever have a voltage on it that is in excess of
the supply voltage or below ground by more than 300 mV,
not even on a transient basis. This can be a problem upon
application of power and power shut-down. Be sure that the
supplies to circuits driving any of the input pins, analog or
digital, do not come up any faster than does the voltage at
the ADC08200 power pins.
4.0 THE DIGITAL INPUT PINS
The ADC08200 has two digital input pins: The PD pin and
the Clock pin.
4.1 The PD Pin
The Power Down (PD) pin, when high, puts the ADC08200
into a low power mode where power consumption is reduced
to 1 mW. Output data is valid and accurate about 1 millisec-
ond after the PD pin is brought low.
The digital output pins retain the last conversion output code
when either the clock is stopped or the PD pin is high.
4.2 The ADC08200 Clock
Although the ADC08200 is tested and its performance is
guaranteed with a 200 MHz clock, it typically will function
well with clock frequencies from 10 MHz to 230 MHz.
The low and high times of the clock signal can affect the
performance of any A/D Converter. Because achieving a
precise duty cycle is difficult, the ADC08200 is designed to
maintain performance over a range of duty cycles. While it is
specified and performance is quaranteed with a 50% clock
duty cycle and 200 Msps, ADC08200 performance is typi-
cally maintained with clock high and low times of 0.65 ns and
0.87 ns, respectively, corresponding to a clock duty cycle
range of 13% to 82.5% with a 200 MHz clock.
The
CLOCK
line should be series terminated at the clock
source in the characteristic impedance of that line. If the
clock line is longer than
20017934
FIGURE 4. The input amplifier should incorporate some gain for best performance (see text).
A
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| ADC0820 | 8-Bit High Speed μP Compatible A/D Converter with Track/Hold Function(8位高速μP兼容A/D轉換器帶跟蹤/保持功能) |
| ADC08234CIMF | IC,QUAD,UART,FIFO |
| ADC08238 | 16 A SPDT MINIATURE POWER RELAY |
| ADC08238BIN | 8-Bit 2 ms Serial I/O A/D Converters with MUX, Reference, and Track/Hold |
| ADC08238BIWM | 8-Bit 2 ms Serial I/O A/D Converters with MUX, Reference, and Track/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC08200CIMT/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08200CIMTX | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08200CIMTX/HAPB | 制造商:Texas Instruments 功能描述: |
| ADC08200CIMTX/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08200EVAL | 功能描述:BOARD EVALUATION FOR ADC08200 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。