- 您現在的位置：買賣IC網 > PDF目錄378278 > ADC081S051CISD (NATIONAL SEMICONDUCTOR CORP) Single Channel, 500 kSPS, 8-Bit A/D Converter PDF資料下載
參數資料
| 型號： | ADC081S051CISD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | ADC |
| 英文描述： | Single Channel, 500 kSPS, 8-Bit A/D Converter |
| 中文描述： | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO6 |
| 封裝： | LLP-6 |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 621K |
| 代理商： | ADC081S051CISD |
Applications Information
(Continued)
5.0 ANALOG INPUTS
An equivalent circuit for one of the ADC081S051’s input
channels is shown in
Figure 7
. Diodes D1 and D2 provide
ESD protection for the analog inputs. At no time should any
input go beyond (V
A
+ 300 mV) or (GND 300 mV), as these
ESD diodes will begin conducting, which could result in
erratic operation.
The capacitor C1 in
Figure 7
has a typical value of 4 pF, and
is mainly the package pin capacitance. Resistor R1 is the on
resistance of the multiplexer and track / hold switch, and is
typically 500 ohms. Capacitor C2 is the ADC081S051 sam-
pling capacitor and is typically 26 pF. The ADC081S051 will
deliver best performance when driven by a low-impedance
source to eliminate distortion caused by the charging of the
sampling capacitance. This is especially important when
using theADC081S051 to sampleAC signals.Also important
when sampling dynamic signals is a band-pass or low-pass
filter to reduce harmonics and noise, improving dynamic
performance.
6.0 DIGITAL INPUTS AND OUTPUTS
The ADC081S051 digital inputs (SCLK and CS) are not
limited by the same absolute maximum ratings as the analog
inputs. The digital input pins are instead limited to +6.5V with
respect to GND, regardless of V
A
, the supply voltage. This
allows the ADC081S051 to be interfaced with a wide range
of logic levels, independent of the supply voltage.
7.0 MODES OF OPERATION
The ADC081S051 has two possible modes of operation:
normal mode, and shutdown mode. The ADC081S051 en-
ters normal mode (and a conversion process is begun) when
CS is pulled low. The device will enter shutdown mode if CS
is pulled high before the tenth falling edge of SCLK after CS
is pulled low, or will stay in normal mode if CS remains low.
Once in shutdown mode, the device will stay there until CS is
brought low again. By varying the ratio of time spent in the
normal and shutdown modes, a system may trade-off
throughput for power consumption.
7.1 Normal Mode
The fastest possible throughput is obtained by leaving the
ADC081S051 in normal mode at all times, so there are no
power-up delays. To keep the device in normal mode con-
tinuously, CS must be kept low until after the 10th falling
edge of SCLK after the start of a conversion (remember that
a conversion is initiated by bringing CS low).
If CS is brought high after the 10th falling edge, but before
the 16th falling edge, the device will remain in normal mode,
but the current conversion will be aborted, and SDATA will
return to TRI-STATE (truncating the output word).
Sixteen SCLK cycles are required to read all of a conversion
word from the device. After sixteen SCLK cycles have
elapsed, CS may be idled either high or low until the next
conversion. If CS is idled low, it must be brought high again
before the start of the next conversion, which begins when
CS is again brought low.
After sixteen SCLK cycles, SDATA returns to TRI-STATE.
Another conversion may be started, after t
QUIET
has
elapsed, by bringing CS low again.
7.2 Shutdown Mode
Shutdown mode is appropriate for applications that either do
not sample continuously, or it is acceptable to trade through-
put for power consumption. When the ADC081S051 is in
shutdown mode, all of the analog circuitry is turned off.
To enter shutdown mode, a conversion must be interrupted
by bringing CS back high anytime between the second and
tenth falling edges of SCLK, as shown in Figure 8. Once CS
has been brought high in this manner, the device will enter
shutdown mode; the current conversion will be aborted and
SDATAwill enter TRI-STATE. If CS is brought high before the
second falling edge of SCLK, the device will not change
mode; this is to avoid accidentally changing mode as a result
of noise on the CS line.
20145514
FIGURE 7. Equivalent Input Circuit
20145516
FIGURE 8. Entering Shutdown Mode
A
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| ADC081S051CISDX | Single Channel, 500 kSPS, 8-Bit A/D Converter |
| ADC081S101 | 1MSPS, 12-/10-/8-Bit A/D Converters in SOT-23 |
| ADC101S021 | Single Channel, 500 kSPS, 8-Bit A/D Converter |
| ADC101S051 | Single Channel, 500 kSPS, 8-Bit A/D Converter |
| ADC081S101CIMFX | 1MSPS, 12-/10-/8-Bit A/D Converters in SOT-23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC081S051CISD/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC081S051CISDX | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC081S051CISDX/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC081S051EVAL | 功能描述:BOARD EVALUATION FOR ADC081S051 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| ADC081S101 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Single Channel, 500 kSPS, 8-Bit A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。