參數資料
型號: ADC08031CIN
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: ADC
英文描述: 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, <BR> Voltage Reference, and Track/Hold Function
中文描述: 8-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP8
封裝: 0.300 INCH, DIP-8
文件頁數: 5/24頁
文件大?。?/td> 509K
代理商: ADC08031CIN
Electrical Characteristics
(Continued)
Note 4:
When the input voltage V
at any pin exceeds the power supplies (V
<
(AGND or DGND) or V
>
V
) the current at that pin should be limited to 5 mA.
The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to four pins.
Note 5:
The maximum power dissipation must be derated at elevated temperatures and is dictated by T
,
θ
and the ambient temperature, T
. The maximum
allowable power dissipation at any temperature is P
= (T
T
)/
θ
or the number given in the Absolute Maximum Ratings, whichever is lower. For devices with
suffixes CIN and CIWM T
= 125C. The typical thermal resistances (
θ
JA
) of these parts when board mounted follow: ADC08031CIN 120C/W, ADC08031CIWM
140C/W, ADC08034 CIWM 140C/W, ADC08038CIWM suffixes 91C/W.
Note 6:
Human body model, 100 pF capacitor discharged through a 1.5 k
resistor.
Note 7:
See AN450 “Surface Mounting Methods and Their Effect on Product Reliability” or Linear Data Book section “Surface Mount” for other methods of soldering
surface mount devices.
Note 8:
Typicals are at T
J
= 25C and represent the most likely parametric norm.
Note 9:
Guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 10:
Total unadjusted error includes offset, full-scale, linearity, multiplexer.
Note 11:
For V
V
the digital code will be 0000 0000. Two on-chip diodes are tied to each analog input (see Block Diagram) which will forward-conduct for
analog input voltages one diode drop below ground or one diode drop greater than V
supply. During testing at low V
levels (e.g., 4.5V), high level analog inputs
(e.g., 5V) can cause an input diode to conduct, especially at elevated temperatures, which will cause errors for analog inputs near full-scale. The spec allows 50 mV
forward bias of either diode; this means that as long as the analog V
does not exceed the supply voltage by more than 50 mV, the output code will be correct. Ex-
ceeding this range on an unselected channel will corrupt the reading of a selected channel.Achievement of an absolute 0 V
DC
to 5 V
DC
input voltage range will there-
fore require a minimum supply voltage of 4.950 V
DC
over temperature variations, initial tolerance and loading.
Note 12:
Channel leakage current is measured after a single-ended channel is selected and the clock is turned off. For off channel leakage current the following two
cases are considered: one, with the selected channel tied high (5 V
) and the remaining seven off channels tied low (0 V
), total current flow through the off chan-
nels is measured; two, with the selected channel tied low and the off channels tied high, total current flow through the off channels is again measured. The two cases
considered for determining on channel leakage current are the same except total current flow through the selected channel is measured.
Note 13:
A 40% to 60% duty cycle range insures proper operation at all clock frequencies. In the case that an available clock has a duty cycle outside of these limits
the minimum time the clock is high or low must be at least 450 ns. The maximum time the clock can be high or low is 100 μs.
Note 14:
Since data, MSB first, is the output of the comparator used in the successive approximation loop, an additional delay is built in (see Block Diagram) to allow
for comparator response time.
Typical Performance Characteristics
Linearity Error vs
Reference Voltage
DS010555-32
Linearity Error vs
Temperature
DS010555-33
Linearity Error vs
Clock Frequency
DS010555-34
Power Supply Current vs
Temperature
DS010555-35
Output Current vs
Temperature
DS010555-36
Power Supply Current
vs Clock Frequency
DS010555-37
www.national.com
5
相關PDF資料
PDF描述
ADC08031CIWM 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function
ADC08034 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function(8位高速串行輸入/輸出A/D轉換器帶多路選擇,電壓基準和跟蹤/保持功能)
ADC08038 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function(8位高速串行輸入/輸出A/D轉換器帶多路選擇,電壓基準和跟蹤/保持功能)
ADC08034CIWM 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function
ADC08032 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function(8位高速串行輸入/輸出A/D轉換器帶多路選擇,電壓基準和跟蹤/保持功能)
相關代理商/技術參數
參數描述
ADC08031CIWM 功能描述:IC ADC 8BIT HS SERIAL I/O 14SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
ADC08031CIWM/NOPB 制造商:Texas Instruments 功能描述:Single ADC SAR 8-bit Serial 14-Pin SOIC W
ADC08031CIWMX 功能描述:IC ADC 8BIT HS SERIAL I/O 14SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
ADC08031CIWMX/NOPB 制造商:Texas Instruments 功能描述:ADC Single SAR 8-bit Serial 14-Pin SOIC W T/R
ADC08031CMJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter, 8-Bit