- 您現在的位置：買賣IC網 > PDF目錄362120 > ADC0803-1CD (NXP SEMICONDUCTORS) CMOS 8-bit A/D converters PDF資料下載
參數資料
| 型號： | ADC0803-1CD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | ADC |
| 英文描述： | CMOS 8-bit A/D converters |
| 中文描述： | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO20 |
| 封裝： | 0.300 INCH, PLASTIC, SOP-20 |
| 文件頁數： | 5/18頁 |
| 文件大小： | 150K |
| 代理商： | ADC0803-1CD |
Philips Semiconductors
Product data
ADC0803/0804
CMOS 8-bit A/D converters
2002 Oct 17
5
AC ELECTRICAL CHARACTERISTICS
SYMBOL
PARAMETER
TO
FROM
TEST CONDITIONS
LIMITS
Typ
UNIT
Min
Max
Conversion time
Clock frequency
1
Clock duty cycle
1
f
CLK
= 1 MHz
1
66
73
μ
s
MHz
f
CLK
0.1
1.0
3.0
40
60
%
CR
Free-running conversion rate
CS = 0, f
CLK
= 1 MHz
INTR tied to WR
13690
conv/s
t
W(
WR)L
t
ACC
Start pulse width
CS = 0
30
ns
Access time
Output
RD
CS = 0, C
L
= 100 pF
C
L
= 10 pF, R
L
= 10 k
See 3-State test circuit
75
100
ns
t
1H
, t
0H
3-State control
Output
RD
70
100
ns
t
W1
, t
R1
INTR delay
INTR
WD
or RD
100
150
ns
C
IN
C
OUT
NOTE:
1. Accuracy is guaranteed at f
CLK
= 1 MHz. Accuracy may degrade at higher clock frequencies.
Logic input=capacitance
5
7.5
pF
3-State output capacitance
5
7.5
pF
FUNCTIONAL DESCRIPTION
These devices operate on the Successive Approximation principle.
Analog switches are closed sequentially by successive
approximation logic until the input to the auto-zero comparator
[ V
IN
(+)–V
IN
(–) ] matches the voltage from the decoder. After all bits
are tested and determined, the 8-bit binary code corresponding to
the input voltage is transferred to an output latch. Conversion begins
with the arrival of a pulse at the WR input if the CS input is low. On
the High-to-Low transition of the signal at the WR or the CS input,
the SAR is initialized, the shift register is reset, and the INTR output
is set high. The A/D will remain in the reset state as long as the CS
and WR inputs remain low. Conversion will start from one to eight
clock periods after one or both of these inputs makes a Low-to-High
transition. After the conversion is complete, the INTR pin will make a
High-to-Low transition. This can be used to interrupt a processor, or
otherwise signal the availability of a new conversion result. A read
(RD) operation (with CS low) will clear the INTR line and enable the
output latches. The device may be run in the free-running mode as
described later. A conversion in progress can be interrupted by
issuing another start command.
Digital Control Inputs
The digital control inputs (CS, WR, RD) are compatible with
standard TTL logic voltage levels. The required signals at these
inputs correspond to Chip Select, START Conversion, and Output
Enable control signals, respectively. They are active-Low for easy
interface to microprocessor and microcontroller control buses. For
applications not using microprocessors, the CS input (Pin 1) can be
grounded and the A/D START function is achieved by a
negative-going pulse to the WR input (Pin 3). The Output Enable
function is achieved by a logic low signal at the RD input (Pin 2),
which may be grounded to constantly have the latest conversion
present at the output.
ANALOG OPERATION
Analog Input Current
The analog comparisons are performed by a capacitive charge
summing circuit. The input capacitor is switched between V
IN(+)
4
and V
IN(–)
, while reference capacitors are switched between taps on
the reference voltage divider string. The net charge corresponds to
the weighted difference between the input and the most recent total
value set by the successive approximation register.
The internal switching action causes displacement currents to flow
at the analog inputs. The voltage on the on-chip capacitance is
switched through the analog differential input voltage, resulting in
proportional currents entering the V
IN(+)
input and leaving the V
IN(–)
input. These transient currents occur at the leading edge of the
internal clock pulses. They decay rapidly so do not inherently cause
errors as the on-chip comparator is strobed at the end of the clock
period.
Input Bypass Capacitors and Source Resistance
Bypass capacitors at the input will average the charges mentioned
above, causing a DC and an AC current to flow through the output
resistance of the analog signal sources. This charge pumping action
is worse for continuous conversions with the V
IN(+)
input at full
scale. This current can be a few microamps, so bypass capacitors
should NOT be used at the analog inputs of the V
REF
/2 input for
high resistance sources (> 1 k
). If input bypass capacitors are
desired for noise filtering and a high source resistance is desired to
minimize capacitor size, detrimental effects of the voltage drop
across the input resistance can be eliminated by adjusting the full
scale with both the input resistance and the input bypass capacitor
in place. This is possible because the magnitude of the input current
is a precise linear function of the differential voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| ADC0803-1CN | CMOS 8-bit A/D converters |
| ADC0803-1LCD | CMOS 8-bit A/D converters |
| ADC0803-1LCN | CMOS 8-bit A/D converters |
| ADC0803CD | CMOS 8-bit A/D converters |
| ADC0803CN | CMOS 8-bit A/D converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC08031CIJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 8-Bit |
| ADC08031CIN | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function |
| ADC08031CIWM | 功能描述:IC ADC 8BIT HS SERIAL I/O 14SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| ADC08031CIWM/NOPB | 制造商:Texas Instruments 功能描述:Single ADC SAR 8-bit Serial 14-Pin SOIC W |
| ADC08031CIWMX | 功能描述:IC ADC 8BIT HS SERIAL I/O 14SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
發布緊急采購，3分鐘左右您將得到回復。