- 您現在的位置：買賣IC網 > PDF目錄16542 > ADA4853-3YRU-EBZ (Analog Devices Inc)BOARD EVAL FOR ADA4853-3YRU PDF資料下載
參數資料
| 型號： | ADA4853-3YRU-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADA4853-3YRU |
| 標準包裝： | 1 |
| 系列： | * |
ADA4853-1/ADA4853-2/ADA4853-3
Rev. F | Page 17 of 20
APPLICATIONS INFORMATION
SINGLE-SUPPLY VIDEO AMPLIFIER
With low differential gain and phase errors and wide 0.5 dB
flatness, the ADA4853-1/ADA4853-2/ADA4853-3 are ideal
solutions for portable video applications. Figure 51 shows a
typical video driver set for a noninverting gain of +2, where
RF = RG = 1 k. The video amplifier input is terminated into a
shunt 75 resistor. At the output, the amplifier has a series
75 resistor for impedance matching to the video load.
When operating in low voltage, single-supply applications, the
input signal is only limited by the input stage headroom.
75
CABLE
VOUT
75
75
VIN
RG
RF
+VS
PD
U1
C1
2.2F
C2
0.01F
05884-
043
+
V
Figure 51. Video Amplifier
POWER SUPPLY BYPASSING
Attention must be paid to bypassing the power supply pins of
the ADA4853-1/ADA4853-2/ADA4853-3. High quality capacitors
with low equivalent series resistance (ESR), such as multilayer
ceramic capacitors (MLCCs), should be used to minimize
supply voltage ripple and power dissipation. A large, usually
tantalum, 2.2 F to 47 F capacitor located in proximity to the
ADA4853-1/ADA4853-2/ADA4853-3 is required to provide
good decoupling for lower frequency signals. The actual value is
determined by the circuit transient and frequency requirements.
In addition, 0.1 F MLCC decoupling capacitors should be
located as close to each of the power supply pins as is physically
possible, no more than inch away. The ground returns should
terminate immediately into the ground plane. Locating the bypass
capacitor return close to the load return minimizes ground loops
and improves performance.
LAYOUT
As is the case with all high speed applications, careful attention
to printed circuit board (PCB) layout details prevents associated
board parasitics from becoming problematic. The ADA4853-1/
ADA4853-2/ADA4853-3 can operate at up to 100 MHz; there-
fore, proper RF design techniques must be employed. The PCB
should have a ground plane covering all unused portions of the
component side of the board to provide a low impedance return
path. Removing the ground plane on all layers from the area
near and under the input and output pins reduces stray capacit-
ance. Signal lines connecting the feedback and gain resistors
should be kept as short as possible to minimize the inductance
and stray capacitance associated with these traces. Termination
resistors and loads should be located as close as possible to their
respective inputs and outputs. Input and output traces should
be kept as far apart as possible to minimize coupling (crosstalk)
through the board. Adherence to microstrip or stripline design
techniques for long signal traces (greater than 1 inch) is
recommended. For more information on high speed board
layout, go to www.analog.com to view A Practical Guide to
High-Speed Printed-Circuit-Board Layout.
相關PDF資料 |
PDF描述 |
|---|---|
| A3CCB-2636G | IDC CABLE- AKC26B/AE26G/AKC26B |
| MCP111T-315E/LB | IC VOLT DET 3.08V LOW SC70-3 |
| 5504971-1 | CABLE ASSEM FIBER SC-SC 1 METER |
| ECE-T2DP392EA | CAP ALUM 3900UF 200V 20% SNAP |
| GMC06DRTH-S734 | CONN EDGECARD 12POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4853-3YRUZ | 功能描述:IC OPAMP VIDEO TRIPLE 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ADA4853-3YRUZ-R7 | 功能描述:IC OPAMP VIDEO TRIPLE 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ADA4853-3YRUZ-RL | 功能描述:IC OPAMP VIDEO TRIPLE 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ADA4855-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Supply, High Speed, Rail-to-Rail Output, Triple Op Amp |
| ADA4855-3YCP-EBZ | 功能描述:BOARD EVAL FOR ADA4855-3YCP RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。