- 您現在的位置：買賣IC網 > PDF目錄67356 > ADA4304-3ACPZ-R7 (ANALOG DEVICES INC) 54 MHz - 865 MHz RF/MICROWAVE SPLITTER PDF資料下載
參數資料
| 型號： | ADA4304-3ACPZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 分路器/合路器 |
| 英文描述： | 54 MHz - 865 MHz RF/MICROWAVE SPLITTER |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, LFCSP, 16 PIN |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 431K |
| 代理商： | ADA4304-3ACPZ-R7 |
ADA4304-3/ADA4304-4
Rev. 0 | Page 10 of 12
APPLICATIONS
The ADA4304-3/ADA4304-4 active splitters are primarily
intended for use in the downstream path of television set-top
boxes (STBs) that contain multiple tuners. They are typically
located directly after the diplexer in a bidirectional CATV
customer premise unit. The ADA4304-3/ADA4304-4 provide a
single-ended input and three or four single-ended outputs that
allow the delivery of the RF signal to multiple signal paths. These
paths can include, but are not limited to, a main picture tuner,
the picture-in-picture (PIP) tuner, an out-of-band (OOB) tuner,
a digital video recorder (DVR), and a cable modem (CM).
The ADA4304-3/ADA4304-4 exhibit composite second-order
(CSO) and composite triple beat (CTB) products that are 62 dBc
and 72 dBc, respectively. The use of the SiGe bipolar process
also allows the ADA4304-3/ADA4304-4 to achieve a noise figure
(NF) of 4.6 dB at 550 MHz.
CIRCUIT DESCRIPTION
The ADA4304-3/ADA4304-4 consist of a low noise buffer
amplifier followed by a resistive power divider. This arrangement
provides 3.3 dB (ADA4304-3) or 2.9 dB (ADA4304-4) of gain
relative to the RF signal present at the input of the device. The
input and each output must be properly matched to a 75 Ω
environment for distortion and noise performance to match
the data sheet specifications. AC coupling capacitors of 0.01 μF
are recommended for the input and outputs.
A 1 μH RF choke (Coilcraft chip inductor 0805LS-102X) is
required to correctly bias the internal nodes of the ADA4304-3/
ADA4304-4. It should be connected between the 5 V supply and
the IL pin (Pin 14). The choke should be placed as close as possible
to the ADA4304-3/ADA4304-4 to minimize parasitic capacitance
on the IL pin, which is critical for achieving the specified
bandwidth and flatness.
EVALUATION BOARDS
The ADA4304-3/ADA4304-4 evaluation board allows designers
to assess the performance of the parts in their particular
application. The board includes 75 Ω coaxial connectors and
75 Ω controlled-impedance signal traces that carry the input
and output signals. Power (5 V) is applied to the red VCC loop
connector, and ground is connected to the black GND loop
connector. Figure 21 is a schematic of the evaluation board. On
the ADA4304-3 evaluation board, connector VO4 and C7 are
not populated.
RF LAYOUT CONSIDERATIONS
Appropriate impedance matching techniques are mandatory
when designing circuit boards for the ADA4304-3/ADA4304-4.
Improper characteristic impedances on traces can cause reflections
that can lead to poor linearity. The characteristic impedance of
the signal trace to the input and from each output should be
75 Ω. Any ground metal on the top surface near signal lines
should be stitched with vias to the internal ground plane, as
shown in Figure 22. The device package exposed paddle must
be reflow soldered to a low inductance ground to achieve data
sheet performance specifications. This is achieved by connecting
the footprint ground pad with vias to a ground plane below
(see Figure 22).
POWER SUPPLY
The 5 V supply should be applied to each VCC pin and RF
choke via a low impedance power bus. The power bus should be
decoupled to ground using a 10 μF tantalum capacitor and a 0.1
μF ceramic chip capacitor located close to the ADA4304-3/
ADA4304-4. In addition, the VCC pins should be decoupled to
ground with a 0.1 μF ceramic chip capacitor located as close to
each pin as possible.
ADA4304-3/
ADA4304-4
L1
1.0μH
GND
VCC
VIN
C2
0.01μF
VO3
C4
0.01μF
VO4
C7
0.01μF
VO1
C6
0.01μF
VO2
C3
0.01μF
C5
10F
+
C1
0.1F
C8
0.1F
VCC
EXPOSED PAD
VCC
GND
VIN
GND
VOUT2
VOUT3
GND
G
N
D
G
N
D
G
N
D
V
O
U
T
4
ADA4304-4 ONLY
V
C
V
C
IL
V
O
U
T
1
07
08
2-
0
06
Figure 21. Evaluation Board Schematic
相關PDF資料 |
PDF描述 |
|---|---|
| ADA4304-3ACPZ-RL | 54 MHz - 865 MHz RF/MICROWAVE SPLITTER |
| ADA4304-4ACPZ-R7 | 54 MHz - 865 MHz RF/MICROWAVE SPLITTER |
| ADA4304-4ACPZ-RL | 54 MHz - 865 MHz RF/MICROWAVE SPLITTER |
| ADG918BRMZ1 | 0 MHz - 2000 MHz RF/MICROWAVE DIVERSITY SWITCH, 1.25 dB INSERTION LOSS |
| ADL5371ACPZ-R2 | 700 MHz - 1300 MHz RF/MICROWAVE QUADRAPHASE MODULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4304-3ACPZ-RL | 功能描述:IC RF SPLITTER 1:3 ACT 16LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 功率分配器/分線器 系列:- 標準包裝:98 系列:- 插入損耗:- 頻率:40MHz ~ 880MHz 技術規格:- 尺寸/尺寸:* 封裝/外殼:- 包裝:管件 |
| ADA4304-4ACPZ-EB | 功能描述:BOARD EVAL FOR ADA4304-4ACP 制造商:analog devices inc. 系列:- 零件狀態:過期 類型:分線器 頻率:54MHz ~ 865MHz 配套使用產品/相關產品:ADA4304-4 所含物品:板 標準包裝:1 |
| ADA4304-4ACPZ-R2 | 功能描述:IC RF SPLITTER ACTIVE 16LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 功率分配器/分線器 系列:- 標準包裝:98 系列:- 插入損耗:- 頻率:40MHz ~ 880MHz 技術規格:- 尺寸/尺寸:* 封裝/外殼:- 包裝:管件 |
| ADA4304-4ACPZ-R7 | 功能描述:IC RF SPLITTER 1:4 SGL 16-LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 功率分配器/分線器 系列:- 標準包裝:98 系列:- 插入損耗:- 頻率:40MHz ~ 880MHz 技術規格:- 尺寸/尺寸:* 封裝/外殼:- 包裝:管件 |
| ADA4304-4ACPZ-RL | 功能描述:IC RF SPLITTER ACTIVE 16LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 功率分配器/分線器 系列:- 標準包裝:98 系列:- 插入損耗:- 頻率:40MHz ~ 880MHz 技術規格:- 尺寸/尺寸:* 封裝/外殼:- 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。