- 您現在的位置：買賣IC網 > PDF目錄375250 > AD9980PCB (Analog Devices, Inc.) High Performance 8-Bit Display Interface PDF資料下載
參數資料
| 型號： | AD9980PCB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | High Performance 8-Bit Display Interface |
| 中文描述： | 高性能8位顯示接口 |
| 文件頁數： | 9/44頁 |
| 文件大?。?/td> | 507K |
| 代理商： | AD9980PCB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9980
Pin
Rev. 0 | Page 9 of 44
Description
External Filter Connection. For proper operation, the pixel clock generator PLL requires an external filter.
Connect the filter shown in Figure 7 to this pin. For optimal performance, minimize noise and parasitics on this
node. For more information see the PCB Layout Recommendations section.
Horizontal Sync Output. A reconstructed and phase-aligned version of the Hsync input. Both the polarity and
duration of this output can be programmed via serial bus registers. By maintaining alignment with DATACK and
Data Outputs, data timing with respect to Hsync can always be determined.
Vertical Sync Output. Pin shared with A0, serial port address. This can be either a separated Vsync from a
composite signal or a direct pass through of the Vsync signal. The polarity of this output can be controlled via a
serial bus bit. The placement and duration in all modes can be set by the graphics transmitter or the duration
can be set by Register 0x14 and Register 0x15. This pin is shared with the A0 function, which does not affect
Vsync output functionality. For more details on A0, see the description in the Serial Control Port section.
Sync-On-Green Slicer Output. This pin outputs one of four possible signals (controlled by Register 0x1D,
Bits [1:0]): raw SOG, raw Hsync, regenerated Hsync from the filter, or the filtered Hsync. See the sync processing
block diagram (Figure 8) to view how this pin is connected. (Besides slicing off SOG, the output from this pin gets
no other additional processing on the AD9980. Vsync separation is performed via the sync separator.)
Odd/Even Field Bit for Interlaced Video.
This output will identify whether the current field (in an interlaced signal) is odd or even.
Serial Port Data I/O.
Serial Port Data Clock.
Serial Port Address Input 0. Pin shared with VSOUT. This pin selects the LSB of the serial port device address,
allowing two Analog Devices parts to be on the same serial bus. A high impedance external pull-up resistor
enables this pin to be read at power-up as 1, or a high impedance, external pull-down resistor enables this pin to
be read at power-up as a 0 and not interfere with the VSOUT functionality. For more details on VSOUT, see the
Outputs section in this table.
Data Output, Red Channel.
Data Output, Green Channel.
Data Output, Blue Channel.
The main data outputs. Bit 7 is the MSB. The delay from pixel sampling time to output is fixed. When the
sampling time is changed by adjusting the phase register, the output timing is shifted as well. The DATACK and
HSOUT outputs are also moved, so the timing relationship among the signals is maintained.
Data Clock Output. This is the main clock output signal used to strobe the output data and HSOUT into external
logic. Four possible output clocks can be selected with Register 0x20, Bits [7:6]. Three of these are related to the
pixel clock (pixel clock, 90° phase-shifted pixel clock, and 2× frequency pixel clock). They are produced either by
the internal PLL clock generator or EXTCLK and are synchronous with the pixel sampling clock. The fourth option
for the data clock output is an internally generated 40 MHz clock.
The sampling time of the internal pixel clock can be changed by adjusting the phase register (Register 0x04).
When this is changed, the pixel related DATACK timing is also shifted. The Data, DATACK, and HSOUT outputs
are all moved so that the timing relationship among the signals is maintained.
Main Power Supply. These pins supply power to the main elements of the circuit. They should be as quiet and
filtered as possible.
Digital Output Power Supply. A large number of output pins (up to 29) switching at high speed (up to 95 MHz)
generate a lot of power supply transients (noise). These supply pins are identified separately from the V
D
pins, so
special care can be taken to minimize output noise transferred into the sensitive analog circuitry. If the AD9980
is interfacing with lower voltage logic, V
DD
may be connected to a lower supply voltage (as low as 1.8 V) for
compatibility.
Clock Generator Power Supply. The most sensitive portion of the AD9980 is the clock generation circuitry. These
pins provide power to the clock PLL and help the user design for optimal performance. The designer should
provide quiet, noise-free power to these pins.
Digital Input Power Supply. This supplies power to the digital logic.
Ground. The ground return for all circuitry on-chip. It is recommended that the AD9980 be assembled on a
single solid ground plane, with careful attention to ground current paths.
FILT
OUTPUTS
HSOUT
VSOUT/A0
SOGOUT
O/E FIELD
SERIAL PORT
SDA
SCL
VSOUT/A0
DATA OUTPUTS
RED [7:0]
GREEN [7:0]
BLUE [7:0]
DATA CLOCK OUTPUT
DATACK
POWER SUPPLY
V
D
(3.3 V)
V
DD
(1.8 V to 3.3 V)
PV
D
(1.8 V)
DAV
DD
(1.8 V)
GND
相關PDF資料 |
PDF描述 |
|---|---|
| AD9994 | 12-Bit CCD Signal Processor with Precision Timing Generator |
| ADA10000S3C | Linear Amplifier MMIC |
| ADA10000 | Linear Amplifier MMIC Data Sheet - Rev 2.3 |
| ADA10000S24Q1 | Linear Amplifier MMIC Data Sheet - Rev 2.3 |
| ADA10000S3CTR | Linear Amplifier MMIC Data Sheet - Rev 2.3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9981 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
| AD9981/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
| AD9981/PCBZ | 制造商:Analog Devices 功能描述:Evaluation Board For The High Performance 10-Bit Display Interface 制造商:Analog Devices 功能描述:EVAL BD FOR THE HI-PERF 10-BIT DISPLAY INTRFC - Bulk |
| AD9981KST-80 | 制造商:Analog Devices 功能描述:HIGH PERFORMANCE 10-BIT DISPLAY INTERFACE - Bulk |
| AD9981KSTZ-80 | 功能描述:IC INTERFACE 10BIT ANALOG 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
發布緊急采購，3分鐘左右您將得到回復。