- 您現在的位置：買賣IC網 > PDF目錄373968 > AD9824KCP (ANALOG DEVICES INC) Complete 14-Bit 30 MSPS CCD Signal Processor PDF資料下載
參數資料
| 型號： | AD9824KCP |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Complete 14-Bit 30 MSPS CCD Signal Processor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC48 |
| 封裝： | 7 X 7 MM, LFCSP-48 |
| 文件頁數： | 21/24頁 |
| 文件大?。?/td> | 438K |
| 代理商： | AD9824KCP |
REV. 0
AD9824
–21–
Internal Power-On Reset Circuitry
After power-on, the AD9824 will automatically reset all internal
registers and perform internal calibration procedures. This takes
approximately 1 ms to complete. During this time, normal
clock signals and serial write operations may occur. However,
serial register writes will be ignored until the internal reset opera-
tion is completed.
Grounding and Decoupling Recommendations
As shown in Figure 33, a single ground plane is recommended
for the AD9824. This ground plane should be as continuous as
possible, particularly around Pins 25 through 39. This will
ensure that all analog decoupling capacitors provide the lowest
possible impedance path between the power and bypass pins and
their respective ground pins. All decoupling capacitors should
be located as close as possible to the package pins. A single clean
power supply is recommended for the AD9824, but a separate
digital driver supply may be used for DRVDD (Pin 13). DRVDD
should always be decoupled to DRVSS (Pin 14), which should
be connected to the analog ground plane. Advantages of using
a separate digital driver supply include using a lower voltage
(2.7 V) to match levels with a 2.7 V ASIC, and reducing digital
power dissipation and potential noise coupling. If the digital
outputs (Pins 1–12) must drive a load larger than 20 pF, buff-
ering is recommended to reduce digital code transition noise.
Alternatively, placing series resistors close to the digital out-
put pins may also help reduce noise.
36
35
34
33
32
31
30
29
28
27
26
25
13 14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
6
7
8
9
10
11
12
37
48 47 46 45 44
39 38
43 42 41 40
PIN 1
(TOP VIEW
AUX1IN
AVSS
AUX2IN
AVDD2
BYP3
NC
CCDIN
BYP2
BYP1
AVDD1
AVSS
AVSS
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
(MSB) D13
AD9824
D
D
S
S
S
S
D
D
V
V
N
D
D
D
D
D
H
P
C
S
S
C
V
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
3V
ANALOG SUPPLY
CCD SIGNAL
3V
ANALOG SUPPLY
14
DATA
OUTPUTS
3
SERIAL
INTERFACE
1.0 F
1.0 F
0.1 F
3V
ANALOG SUPPLY
8
CLOCK
INPUTS
0.1 F
0.1 F
3V
ANALOG SUPPLY
3V
DRIVER
SUPPLY
NC = NO CONNECT
N
Figure 33. Recommended Circuit Configuration for CCD-Mode
相關PDF資料 |
PDF描述 |
|---|---|
| AD9824 | Complete 14-Bit 30 MSPS CCD Signal Processor |
| AD9826KRS | Complete 16-Bit Imaging Signal Processor |
| AD9826 | Complete 16-Bit Imaging Signal Processor |
| AD9830 | CMOS Complete DDS |
| AD9830AST | CMOS Complete DDS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9824KCPRL | 制造商:Analog Devices 功能描述:AFE Video 1ADC 14-Bit 3.3V 48-Pin LFCSP EP T/R |
| AD9824KCPZ | 功能描述:IC CCD SIGNAL PROC 14BIT 48LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9824KCPZ | 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS)) |
| AD9824KCPZRL | 功能描述:IC CCD SIGNAL PROC 14BIT 48LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9826 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 16-Bit Imaging Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。