參數資料
型號： AD9788BSVZ
廠商： Analog Devices Inc
文件頁數： 27/64頁
文件大小： 0K
描述： IC DAC 16BIT 800MSPS 100TQFP
產品培訓模塊： Data Converter Fundamentals
DAC Architectures
設計資源： Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141)
標準包裝： 1
系列： TxDAC®
位數： 16
數據接口： 串行
轉換器數目： 2
電壓電源： 模擬和數字
功率耗散（最大）： 450mW
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-TQFP 裸露焊盤
供應商設備封裝： 100-TQFP-EP（14x14）
包裝： 托盤
輸出數目和類型： 4 電流，單極；4 電流，雙極
采樣率（每秒）： 800M
產品目錄頁面： 785 (CN2011-ZH PDF)
AD9785/AD9787/AD9788
Rev. A | Page 33 of 64
INPUT DATA PORTS
The AD9785/AD9787/AD9788 can operate in two data input
modes: dual-port mode and single-port mode. In the default
dual-port mode (single-port mode = 0), each DAC receives data
from a dedicated input port. In single-port mode (single-port
mode = 1), both DACs receive data from Port 1. In single-port
mode, DAC 1 and DAC 2 data is interleaved and the TXENABLE
input is used to steer data to the intended DAC. In dual-port
mode, the TXENABLE input is used to power down the digital
datapath.
In dual-port mode, the data must be delivered at the input data
rate. In single-port mode, data must be delivered at twice the
input data rate of each DAC. Because the data inputs function up
to a maximum of 300 MSPS, it is only practical to operate with
input data rates up to 150 MHz per DAC in single-port mode.
In both dual-port and single-port modes, a data clock output
(DATACLK) signal is available as a fixed-time base with which
to drive data from an FPGA (field programmable gate array) or
from another data source. This output signal operates at the
input data rate. The DATACLK pin can operate as either an
input or an output.
SINGLE-PORT MODE
In single-port mode, data for both DACs is received on the
Port 1 input bus (P1D[15:0]). I and Q data samples are inter-
leaved and are latched on the rising edges of DATACLK.
Accompanying the data is the TXENABLE (Pin 39) input
signal, which steers incoming data to its respective DAC. When
TXENABLE is high, the corresponding data-word is sent to the
I DAC and, when TXENABLE is low, the corresponding data is
sent to the Q DAC. The timing of the digital interface in
interleaved mode is shown in Figure 48.
The Q first bit (Register 0x01, Bit 1) controls the pairing
order of the input data. With the Q first bit set to the default
of 0, the I/Q pairing sent to the DACs is the two input data-
words corresponding to TXENABLE low followed by
TXENABLE high.
With the Q first bit set to 1, the I/Q pairing sent to the DACs is
the two input data-words corresponding to TXENABLE high
followed by TXENABLE low. Note that with Q first set, the
I data still corresponds to the TXENABLE high word and the
Q data corresponds to the TXENABLE low word and only the
pairing order changes.
DUAL-PORT MODE
In dual-port mode, data for each DAC is received on the
respective input bus (P1D[15:0] or P2D[15:0]). I and Q data
arrive simultaneously and are sampled on the rising edge of an
internal sampling clock (SMP_CLK) that is synchronous with
DATACLK. In dual-port mode, driving the TXENABLE input
low powers down the digital datapath. TXENABLE should be
held high during normal data transmission.
INPUT DATA REFERENCED TO DATACLK
The simplest method of interfacing to the AD9785/AD9787/
AD9788 is when the input data is referenced to the DATACLK
output. The DATACLK output is phase-locked (with some
offset) to the internal clock that is used to latch the input data.
Therefore, if the setup and hold times of the input data with
respect to DATACLK are met, the interface timing latches in the
data correctly.
Table 25 shows the setup and hold time requirements for the
input data over the operating temperature range of the device.
Table 25 also shows the data valid window (DVW). The data
valid window is the sum of the setup and hold times of the
interface. This is the minimum amount of time valid data must
be presented to the device in order to ensure proper sampling.
相關PDF資料
PDF描述
SI5316-C-GM IC PREC JITTER ATTENUATOR 36-QFN
AD7839ASZ IC DAC 13BIT OCTAL V-OUT 44-MQFP
AD5360BSTZ IC DAC 16BIT 16CH SERIAL 52-LQFP
AD5764BSUZ IC DAC 16BIT QUAD VOUT 32-TQFP
VE-J53-MZ-F4 CONVERTER MOD DC/DC 24V 25W
相關代理商/技術參數
參數描述
AD9788BSVZRL 功能描述:IC DAC 16BIT 800MSPS 100TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
AD9788-DPG2-EBZ 功能描述:BOARD EVALUATION FOR AD9788 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD9788-EBZ 制造商:Analog Devices 功能描述:Evaluation Board For AD9788 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board
AD9788MOD-EBZ 制造商:Analog Devices 功能描述:DUAL 12-/14-/16-BIT 800 MSPS DAC WITH LOW POWER 32-BIT COMPLEX NCO 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk
AD9789BBC 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*