參數資料
型號： AD9742ARUZ
廠商： Analog Devices Inc
文件頁數： 9/32頁
文件大?。?/td> 0K
描述： IC DAC 12BIT 210MSPS 28-TSSOP
產品培訓模塊： Data Converter Fundamentals
DAC Architectures
標準包裝： 50
系列： TxDAC®
設置時間： 11ns
位數： 12
數據接口： 并聯
轉換器數目： 1
電壓電源： 模擬和數字
功率耗散（最大）： 145mW
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 28-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 28-TSSOP
包裝： 管件
輸出數目和類型： 2 電流，單極；2 電流，雙極
采樣率（每秒）： 210M
產品目錄頁面： 785 (CN2011-ZH PDF)
配用： AD9742ACP-PCBZ-ND - BOARD EVAL FOR AD9742ACP
Data Sheet
AD9742
Rev. C | Page 17 of 32
SINGLE-ENDED, UNBUFFERED VOLTAGE OUTPUT
Figure 34 shows the AD9742 configured to provide a unipolar
output range of approximately 0 V to 0.5 V for a doubly terminated
50 cable since the nominal full-scale current, IOUTFS, of 20 mA
flows through the equivalent RLOAD of 25 . In this case, RLOAD
represents the equivalent load resistance seen by IOUTA or
IOUTB. The unused output (IOUTA or IOUTB) can be connected
to ACOM directly or via a matching RLOAD. Different values of
IOUTFS and RLOAD can be selected as long as the positive compliance
range is adhered to. One additional consideration in this mode
is the integral nonlinearity (INL), discussed in the Analog Outputs
section. For optimum INL performance, the single-ended, buffered
voltage output configuration is suggested.
AD9742
IOUTA
IOUTB
50
25
VOUTA = 0V TO 0.5V
IOUTFS = 20mA
50
22
21
02912-B-033
Figure 34. 0 V to 0.5 V Unbuffered Voltage Output
SINGLE-ENDED, BUFFERED VOLTAGE OUTPUT
CONFIGURATION
Figure 35 shows a buffered single-ended output configuration
in which the op amp U1 performs an I-V conversion on the
AD9742 output current. U1 maintains IOUTA (or IOUTB) at a
virtual ground, minimizing the nonlinear output impedance
effect on the DAC’s INL performance as described in the Analog
Outputs section. Although this single-ended configuration typically
provides the best dc linearity performance, its ac distortion
performance at higher DAC update rates may be limited by U1’s
slew rate capabilities. U1 provides a negative unipolar output
voltage, and its full-scale output voltage is simply the product of
RFB and IOUTFS. The full-scale output should be set within U1’s
voltage output swing capabilities by scaling IOUTFS and/or RFB. An
improvement in ac distortion performance may result with a
reduced IOUTFS since U1 will be required to sink less signal current.
AD9742
IOUTA
IOUTB
COPT
200
U1
VOUT = IOUTFS × RFB
IOUTFS = 10mA
RFB
200
22
21
02912-B-034
Figure 35. Unipolar Buffered Voltage Output
POWER AND GROUNDING CONSIDERATIONS,
POWER SUPPLY REJECTION
Many applications seek high speed and high performance under
less than ideal operating conditions. In these application circuits,
the implementation and construction of the printed circuit
board is as important as the circuit design. Proper RF techniques
must be used for device selection, placement, and routing as
well as power supply bypassing and grounding to ensure
optimum performance. Figure 40 to Figure 43 illustrate the
recommended printed circuit board ground, power, and signal
plane layouts implemented on the AD9742 evaluation board.
One factor that can measurably affect system performance is
the ability of the DAC output to reject dc variations or ac noise
superimposed on the analog or digital dc power distribution.
This is referred to as the power supply rejection ratio (PSRR).
For dc variations of the power supply, the resulting performance
of the DAC directly corresponds to a gain error associated with
the DAC’s full-scale current, IOUTFS. AC noise on the dc supplies
is common in applications where the power distribution is
generated by a switching power supply. Typically, switching
power supply noise will occur over the spectrum from tens of
kHz to several MHz. The PSRR versus frequency of the AD9742
AVDD supply over this frequency range is shown in Figure 36.
FREQUENCY (MHz)
85
40
12
6
8
10
0
PSRR
(dB)
80
75
70
65
60
55
50
2
4
45
02912-B-035
Figure 36. Power Supply Rejection Ratio (PSRR)
Note that the ratio in Figure 36 is calculated as amps out/volts
in. Noise on the analog power supply has the effect of modulating
the internal switches, and therefore the output current. The
voltage noise on AVDD, therefore, will be added in a nonlinear
manner to the desired IOUT. Due to the relative different size of
these switches, the PSRR is very code dependent. This can produce
a mixing effect that can modulate low frequency power supply
noise to higher frequencies. Worst-case PSRR for either one of
the differential DAC outputs will occur when the full-scale current
is directed toward that output. As a result, the PSRR measurement
in Figure 36 represents a worst-case condition in which the
digital inputs remain static and the full-scale output current of
20 mA is directed to the DAC output being measured.
相關PDF資料
PDF描述
LTC1590CN#PBF IC D/A CONV 12BIT DUAL 16-DIP
AD5726YRSZ-REEL IC DAC 12BIT QUAD SERIAL 16-SSOP
ICS873990AYLFT IC CLK GEN LV LVPECL 52-LQFP
VI-B4F-MY-F4 CONVERTER MOD DC/DC 72V 50W
VI-B4F-MY-F3 CONVERTER MOD DC/DC 72V 50W
相關代理商/技術參數
參數描述
AD9742ARUZRL7 功能描述:IC DAC 12BIT 210MSPS 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:*
AD9742ARZ 功能描述:IC DAC 12BIT 210MSPS 28-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:*
AD9742ARZRL 功能描述:IC DAC 12BIT 210MSPS 28-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:*
AD9742-EB 制造商:Analog Devices 功能描述:EVAL BOARDFOR AD9742 - Bulk
AD9742-EBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 210 MSPS TxDAC Digital-to-Analog Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*