- 您現在的位置：買賣IC網 > PDF目錄17059 > AD9704-DPG2-EBZ (Analog Devices Inc)BOARD EVAL FOR AD9704 PDF資料下載
參數資料
| 型號： | AD9704-DPG2-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 35/44頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9704 |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9704/AD9705/AD9706/AD9707
Data Sheet
Rev. B | Page 40 of 44
APPLICATIONS INFORMATION
OUTPUT CONFIGURATIONS
The following sections illustrate some typical output
Unless otherwise noted, it is assumed that IOUTFS is set to a
nominal 2 mA. For applications requiring the optimum
dynamic performance, a differential output configuration is
suggested. A differential output configuration can consist of
either an RF transformer or a differential op amp configuration.
The transformer configuration provides the optimum high
frequency performance and is recommended for any application
that allows ac coupling. The differential op amp configuration is
suitable for applications requiring dc coupling, signal gain,
and/or a low output impedance.
A single-ended output is suitable for applications where low
cost and low power consumption are primary concerns.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-single-
ended signal conversion, as shown in Figure 88. The distortion
performance of a transformer typically exceeds that available from
standard op amps, particularly at higher frequencies. Transformer
coupling provides excellent rejection of common-mode distortion
(that is, even-order harmonics) over a wide frequency range. It
also provides electrical isolation and can deliver voltage gain
without adding noise. Transformers with different impedance
ratios can also be used for impedance matching purposes. The
main disadvantages of transformer coupling are the low frequency
roll-off, lack of power gain, and the higher output impedance.
AD9704/AD9705
AD9706/AD9707
IOUTB
IOUTA
20
21
OPTIONAL RDIFF
RLOAD
05
92
6-
0
95
Figure 88. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
connected to a voltage that keeps the voltages on IOUTA and
IOUTB within the output common voltage range of the device.
Note that the dc component of the DAC output current is equal
to IFS/2 and flows out of both IOUTA and IOUTB. The center
tap of the transformer should provide a path for this dc current.
In many applications, AGND provides the most convenient
voltage for the transformer center tap. The complementary
voltages appearing at IOUTA and IOUTB (that is, VIOUTA and
VIOUTB) swing symmetrically around AGND and should be
maintained with the specified output compliance range of the
A differential resistor, RDIFF, can be inserted in applications
where the output of the transformer is connected to the load,
RLOAD, via a passive reconstruction filter or cable. RDIFF, as
reflected by the transformer, is chosen to provide a source
termination that results in a low VSWR. Note that approxi-
mately half the signal power is dissipated across RDIFF.
SINGLE-ENDED BUFFERED OUTPUT USING AN OP
AMP
An op amp, such as the ADA4899-1, can be used to perform a
single-ended current-to-voltage conversion, as shown in Figure 89.
pair of series resistors, RS, off each output. The feedback resistor,
RFB, determines the peak signal swing by the following formula:
2
FS
FB
OUT
I
R
V
×
=
The common-mode voltage of the output is determined by the
following formula:
OUT
B
FB
REF
CM
V
R
V
+
×
=
1
The maximum and minimum voltages out of the amplifier are,
respectively, the following:
+
×
=
B
FB
REF
MAX
R
V
1
VMIN = VMAX IFS × RFB
+5V
AD9704/AD9705
AD9706/AD9707
IOUTA
IOUTB 20
RFB
VOUT
REFIO 23
21
RS
OTCM 19
CF
C
RS
RB
059
26
-10
0
+
–
ADA4899-1
–5V
Figure 89. Single-Supply Single-Ended Buffer
相關PDF資料 |
PDF描述 |
|---|---|
| AD9741-DPG2-EBZ | IC DAC DUAL 8BIT 200MSPS 72LFCSP |
| 0210490186 | CABLE JUMPER 1.25MM .254M 12POS |
| AD9743-DPG2-EBZ | IC DAC DUAL 10BIT 72LFCSP |
| AD9116-DPG2-EBZ | IC DAC DUAL 12BIT LO PWR 40LFCSP |
| VE-B4X-EY | CONVERTER MOD DC/DC 5.2V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9704-EB | 制造商:Analog Devices 功能描述: |
| AD9705BCPZ | 功能描述:IC DAC TX 10BIT 175MSPS 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD9705BCPZRL7 | 功能描述:IC DAC TX 10BIT 175MSPS 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD9705-DPG2-EBZ | 功能描述:BOARD EVAL FOR AD9705 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9705EB | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。