參數資料
型號： AD9520-0BCPZ-REEL7
廠商： Analog Devices Inc
文件頁數： 66/80頁
文件大?。?/td> 0K
描述： IC CLOCK GEN 2.8GHZ VCO 64LFCSP
設計資源： Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121)
Phase Coherent FSK Modulator (CN0186)
標準包裝： 750
類型： 時鐘發生器，扇出配送
PLL： 是
輸入： CMOS，LVDS，LVPECL
輸出： CMOS，LVPECL
電路數： 1
比率 - 輸入:輸出： 2:12，2:24
差分 - 輸入:輸出： 是/是
頻率 - 最大： 2.95GHz
除法器/乘法器： 是/無
電源電壓： 3.135 V ~ 3.465 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤，CSP
供應商設備封裝： 64-LFCSP-VQ（9x9）
包裝： 帶卷 (TR)
Data Sheet
AD9520-0
Rev. A | Page 69 of 80
Reg.
Addr.
(Hex) Bits Name
Description
[4:0] REFMON pin
control
Selects the signal that is connected to the REFMON pin.
Bit
4
Bit
3
Bit
2
Bit
1
Bit
0
Level or
Dynamic
Signal
Signal at REFMON Pin
0
LVL
Ground, dc (default).
0
1
DYN
REF1 clock (differential reference when in differential mode).
0
1
0
DYN
REF2 clock (N/A in differential mode).
0
1
DYN
Selected reference to PLL (differential reference when in differential mode).
0
1
0
DYN
Unselected reference to PLL (not available in differential mode).
0
1
0
1
LVL
Status of selected reference (status of differential reference); active high.
0
1
0
LVL
Status of unselected reference (not available in differential mode); active high.
0
1
LVL
Status of REF1 frequency; active high.
0
1
0
LVL
Status of REF2 frequency; active high.
0
1
0
1
LVL
(Status of REF1 frequency) AND (status of REF2 frequency).
0
1
0
1
0
LVL
(DLD) AND (status of selected reference) AND (status of VCO).
0
1
0
1
LVL
Status of VCO frequency; active high.
0
1
0
LVL
Selected reference (low = REF1, high = REF2).
0
1
0
1
LVL
DLD; active high.
0
1
0
LVL
Holdover active; active high.
0
1
LVL
N/A. Do not use.
1
0
LVL
VS (PLL power supply).
1
0
1
DYN
REF1 clock (differential reference when in differential mode).
1
0
1
0
DYN
REF2 clock (not available in differential mode).
1
0
1
DYN
Selected reference to PLL (differential reference when in differential mode).
1
0
1
0
DYN
Unselected reference to PLL (not available when in differential mode).
1
0
1
0
1
LVL
Status of selected reference (status of differential reference); active low.
1
0
1
0
LVL
Status of unselected reference (not available in differential mode); active low.
1
0
1
LVL
Status of REF1 frequency; active low.
1
0
LVL
Status of REF2 frequency; active low.
1
0
1
LVL
(Status of REF1 frequency) AND (status of REF2 frequency).
1
0
1
0
LVL
(DLD) AND (status of selected reference) AND (status of VCO).
1
0
1
LVL
Status of VCO frequency; active low.
1
0
LVL
Selected reference (low = REF2, high = REF1).
1
0
1
LVL
DLD; active low.
1
0
LVL
Holdover active; active low.
1
LVL
N/A. Do not use.
0x01C 7
Disable
switchover
deglitch
Disables or enables the switchover deglitch circuit.
0: enables the switchover deglitch circuit (default).
1: disables the switchover deglitch circuit.
6
Select REF2
If Register 0x01C[5] = 0b, selects the reference for PLL when in manual; register selected reference control.
0: selects REF1 (default).
1: selects REF2.
5
Use REF_SEL pin If Register 0x01C[4] = 0b (manual), sets the method of PLL reference selection.
0: uses Register 0x01C[6] (default).
1: uses REF_SEL pin.
4
Enable automatic
reference
switchover
Automatic or manual reference switchover. Single-ended reference mode must be selected by Register 0x01C[0] = 0b.
0: manual reference switchover (default).
1: automatic reference switchover. Setting this bit also powers on REF1 and REF2 and overrides the settings in Register 0x01C[2:1].
3
Stay on REF2
Stays on REF2 after switchover.
0: returns to REF1 automatically when REF1 status is good again (default).
1: stays on REF2 after switchover. Does not automatically return to REF1.
2
Enable REF2
This bit turns the REF2 power on. This bit is overridden when automatic reference switchover is enabled.
0: REF2 power off (default).
1: REF2 power on.
1
Enable REF1
This bit turns the REF1 power on. This bit is overridden when automatic reference switchover is enabled.
0: REF1 power off (default).
1: REF1 power on.
0
Enable
differential ref
Selects the PLL reference mode, differential or single-ended. Register 0x01C[2:1] should be cleared when this bit is set.
0: single-ended reference mode (default); 1: differential reference mode.
相關PDF資料
PDF描述
AD9520-1BCPZ IC CLOCK GEN 2.5GHZ VCO 64LFCSP
AD9520-2BCPZ IC CLOCK GEN 2.2GHZ VCO 64LFCSP
AD9520-3BCPZ-REEL7 IC CLOCK GEN 2GHZ VCO 64LFCSP
AD9520-4BCPZ-REEL7 IC CLOCK GEN 1.6GHZ VCO 64LFCSP
AD9520-5BCPZ-REEL7 IC CLOCK GEN EXT VCO 64LFCSP
相關代理商/技術參數
參數描述
AD9520-1 制造商:AD 制造商全稱:Analog Devices 功能描述:12 LVPECL/24 CMOS Output Clock Generator with Integrated 2.5 GHz VCO
AD9520-1/PCBZ 功能描述:BOARD EVAL FOR AD9520-1 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
AD9520-1BCPZ 功能描述:IC CLOCK GEN 2.5GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
AD9520-1BCPZ-REEL7 功能描述:IC CLOCK GEN 2.5GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
AD9520-2 制造商:AD 制造商全稱:Analog Devices 功能描述:12 LVPECL/24 CMOS Output Clock Generator with Integrated 2.2 GHz VCO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*