參數資料
型號: AD9276-65EBZ
廠商: Analog Devices Inc
文件頁數: 17/48頁
文件大?。?/td> 0K
描述: BOARD EVALUATION FOR AD9276
設計資源: AD9276/77 Eval Brd Gerber Files
標準包裝: 1
ADC 的數量: 1
位數: 12
采樣率(每秒): 65M
數據接口: 串行,SPI?
輸入范圍: 733 mVpp
在以下條件下的電源(標準): 195mW @ 40MSPS
工作溫度: -40°C ~ 85°C
已用 IC / 零件: AD9276
已供物品:
AD9276
Rev. 0 | Page 24 of 48
LNA Noise
The short-circuit noise voltage (input-referred noise) is an
important limit on system performance. The short-circuit noise
voltage for the LNA is 0.75 nV/√Hz at a gain of 21.3 dB, including
the VGA noise at a VGA postamp gain of 27 dB. These measure-
ments, which were taken without a feedback resistor, provide
the basis for calculating the input noise and noise figure (NF)
performance of the configurations shown in Figure 49.
VOUT
UNTERMINATED
+
LI-x
RIN
RS
VOUT
RESISTIVE TERMINATION
+
LI-x
RIN
RS
VOUT
ACTIVE IMPEDANCE MATCH
+
LI-x
RIN
RFB
1 + A/2
RS
RIN =
08
18
0-
0
43
Figure 49. Input Configurations
Figure 50 and Figure 51 are simulations of noise figure vs. RS
results using these configurations and an input-referred noise
voltage of 3.8 nV/√Hz for the VGA. Unterminated (RFB = ∞)
operation exhibits the lowest equivalent input noise and noise
figure. Figure 51 shows the noise figure vs. source resistance
rising at low RS—where the LNA voltage noise is large compared
with the source noise—and at high RS due to the noise contribution
from RFB. The lowest NF is achieved when RS matches RIN.
The main purpose of input impedance matching is to improve
the transient response of the system. With resistive termination,
the input noise increases due to the thermal noise of the match-
ing resistor and the increased contribution of the LNA’s input
voltage noise generator. With active impedance matching,
however, the contributions of both are smaller (by a factor of
1/(1 + LNA gain)) than they would be for resistive termination.
Figure 50 shows the relative noise figure performance. With an
LNA gain of 21.3 dB, the input impedance was swept with RS to
preserve the match at each point. The noise figures for a source
impedance of 50 Ω are 7.3 dB, 4.2 dB, and 2.8 dB for the resistive
termination, active termination, and unterminated configurations,
respectively. The noise figures for 200 Ω are 4.5 dB, 1.7 dB, and
1.0 dB, respectively.
Figure 51 shows the noise figure as it relates to RS for various
values of RIN, which is helpful for design purposes.
10
100
1k
0
1.5
3.0
4.5
6.0
7.5
9.0
10.5
12.0
RS ()
NO
IS
E
F
IG
U
RE
(
d
B)
UNTERMINATED
RESISTIVE TERMINATION
ACTIVE TERMINATION
08
18
0-
0
44
Figure 50. Noise Figure vs. RS for Resistive Termination, Active
Termination Matched, and Unterminated Inputs, VGAIN = 0.8 V
10
100
1k
0
1
2
3
4
5
6
7
8
RS ()
NO
IS
E
F
IG
U
RE
(
d
B)
RIN = 50
RIN = 75
RIN = 100
RIN = 200
UNTERMINATED
08
18
0-
0
45
Figure 51. Noise Figure vs. RS for Various Fixed Values of RIN,
Active Termination Matched Inputs, VGAIN = 0.8 V
相關PDF資料
PDF描述
FPF2101 IC SWITCH LOAD FULL FUNC SOT23-5
AD9257-65EBZ BOARD EVAL FOR AD9257
GMM10DRYH CONN EDGECARD 20POS DIP .156 SLD
AD9253-125EBZ BOARD EVAL FOR AD9253-125
GCM15DRYF CONN EDGECARD 30POS DIP .156 SLD
相關代理商/技術參數
參數描述
AD9276-80KITZ 功能描述:BOARD EVAL HI SPEED FPGA AD9276 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
AD9276BSVZ 功能描述:IC ADC 12BIT LNA/VGA/AAF 100TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD9276XBCZ 功能描述:IC ADC 12BIT LNA/VGA/AAF 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
AD9276XSVZ 功能描述:IC ADC 12BIT LNA/VGA/AAF 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
AD9277 制造商:AD 制造商全稱:Analog Devices 功能描述:Octal LNA/VGA/AAF/14-Bit ADC and CW I/Q Demodulator