參數資料
型號： AD9238BCPZ-65
廠商： Analog Devices Inc
文件頁數： 11/48頁
文件大小： 0K
描述： IC ADC 12BIT DUAL 65MSPS 64LFCSP
標準包裝： 1
位數： 12
采樣率（每秒）： 65M
數據接口： 并聯
轉換器數目： 2
功率耗散（最大）： 600mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤，CSP
供應商設備封裝： 64-LFCSP-VQ（9x9）
包裝： 托盤
輸入數目和類型： 4 個單端，單極；2 個差分，單極
配用： AD9238BCP-65EBZ-ND - BOARD EVAL WITH AD9238BCP-65
AD9238
Rev. C | Page 19 of 48
DATA FORMAT
The AD9238 data output format can be configured for either
twos complement or offset binary. This is controlled by the data
format select pin (DFS). Connecting DFS to AGND produces
offset binary output data. Conversely, connecting DFS to AVDD
formats the output data as twos complement.
The output data from the dual ADCs can be multiplexed onto a
single 12-bit output bus. The multiplexing is accomplished by
toggling the MUX_SELECT bit, which directs channel data to
the same or opposite channel data port. When MUX_SELECT
is logic high, the Channel A data is directed to the Channel A
output bus, and the Channel B data is directed to the Channel B
output bus. When MUX_SELECT is logic low, the channel data
is reversed, that is the Channel A data is directed to the
Channel B output bus, and the Channel B data is directed to the
Channel A output bus. By toggling the MUX_SELECT bit,
multiplexed data is available on either of the output data ports.
If the ADCs run with synchronized timing, this same clock can
be applied to the MUX_SELECT pin. Any skew between CLK_A,
CLK_B, and MUX_SELECT can degrade ac performance. It is
recommended to keep the clock skew <100 pS. After the
MUX_SELECT rising edge, either data port has the data for its
respective channel; after the falling edge, the alternate channel’s
data is placed on the bus. Typically, the other unused bus would
be disabled by setting the appropriate OEB high to reduce
power consumption and noise. Figure 34 shows an example of
multiplex mode. When multiplexing data, the data rate is two
times the sample rate. Note that both channels must remain
active in this mode and that each channel’s power-down pin
must remain low.
VOLTAGE REFERENCE
A stable and accurate 0.5 V voltage reference is built into the
AD9238. The input range can be adjusted by varying the reference
voltage applied to the AD9238, using either the internal
reference with different external resistor configurations or an
externally applied reference voltage. The input span of the ADC
tracks reference voltage changes linearly. If the ADC is being
driven differentially through a transformer, the reference voltage
can be used to bias the center tap (common-mode voltage).
The shared reference mode allows the user to connect the references
from the dual ADCs together externally for superior gain and
offset matching performance. If the ADCs are to function
independently, the reference decoupling can be treated
independently and can provide superior isolation between the dual
channels. To enable shared reference mode, the SHARED_REF
pin must be tied high and the external differential references
must be externally shorted. (REFT_A must be externally
shorted to REFT_B, and REFB_A must be shorted to REFB_B.)
Internal Reference Connection
A comparator within the AD9238 detects the potential at the
SENSE pin and configures the reference into four possible states,
which are summarized in Table 7. If SENSE is grounded, the
reference amplifier switch is connected to the internal resistor
divider (see Figure 35), setting VREF to 1 V. Connecting the
SENSE pin to VREF switches the reference amplifier output to
the SENSE pin, completing the loop and providing a 0.5 V
reference output. If a resistor divider is connected, as shown in
Figure 36, the switch is again set to the SENSE pin. This puts
the reference amplifier in a noninverting mode with the VREF
output defined as
VREF = 0.5 × (1 + R2/R1)
In all reference configurations, REFT and REFB drive the ADC
core and establish its input span. The input range of the ADC
always equals twice the voltage at the reference pin for either an
internal or an external reference.
VIN+
VIN–
10
μF
10
μF
0.1
μF
0.1
μF
REFT
ADC
CORE
SELECT
LOGIC
SENSE
0.1
μF
0.5V
AD9238
REFB
0.1
μF
VREF
02640-034
Figure 35. Internal Reference Configuration
Table 7. Reference Configuration Summary
Selected Mode
SENSE Voltage
Resulting VREF (V)
Resulting Differential Span (V p-p)
External Reference
AVDD
N/A
2 × External Reference
Internal Fixed Reference
VREF
0.5
1.0
Programmable Reference
0.2 V to VREF
0.5 × (1 + R2/R1)
2 × VREF (See Figure 36)
Internal Fixed Reference
AGND to 0.2 V
1.0
2.0
相關PDF資料
PDF描述
AD9238BSTZ-65 IC ADC 12BIT DUAL 65MSPS 64-LQFP
ICL3226ECA IC TXRX RS-232 3-5.5V ESD 16SSOP
AD9480ASUZ-250 IC ADC 8BIT 250MSPS 3.3V 44TQFP
AD977CNZ IC ADC 16BIT 100KSPS 20-DIP
MS3101R16S-4S CONN RCPT 2POS PANEL MNT W/SCKT
相關代理商/技術參數
參數描述
AD9238BCPZ-65EB 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 20 MSPS/40 MSPS/65 MSPS Dual A/D Converter
AD9238BCPZRL-20 功能描述:IC ADC 12BIT DUAL 20MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD9238BCPZRL-40 功能描述:IC ADC 12BIT DUAL 40MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD9238BCPZRL-65 功能描述:IC ADC 12BIT DUAL 65MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9238BST-20 功能描述:IC ADC 12BIT DUAL 20MSPS 64-LQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*