- 您現在的位置：買賣IC網 > PDF目錄8647 > AD9115BCPZRL7 (Analog Devices Inc)IC DAC DUAL 10BIT LO PWR 40LFCSP PDF資料下載
參數資料
| 型號： | AD9115BCPZRL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 38/52頁 |
| 文件大小： | 0K |
| 描述： | IC DAC DUAL 10BIT LO PWR 40LFCSP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 750 |
| 系列： | TxDAC® |
| 位數： | 10 |
| 數據接口： | 串行 |
| 轉換器數目： | 2 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 232mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 40-LFCSP-VQ（6x6） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 4 電流，單極 |
| 采樣率（每秒）： | 125M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Data Sheet
AD9114/AD9115/AD9116/AD9117
Rev. C | Page 43 of 52
REFERENCE OPERATION
The AD9114/AD9115/AD9116/AD9117 contains an internal
1.0 V band gap reference. The internal reference can be disabled by
setting Bit 0 (EXTREF) of the power-down register (Address 0x01)
through the SPI interface. To use the internal reference, decouple
the REFIO pin to AVSS with a 0.1 μF capacitor, enable the
internal reference, and clear Bit 0 of the power-down register
(Address 0x01) through the SPI interface. Note that this is the
default configuration. The internal reference voltage is present
at REFIO. If the voltage at REFIO is to be used anywhere else in
the circuit, an external buffer amplifier with an input bias current of
less than 100 nA must be used to avoid loading the reference. An
example of the use of the internal reference is shown in Figure 96.
CURRENT
SCALING
x32
AD9114/AD9115/
AD9116/AD9117
I DAC
OR
Q DAC
07466-
218
IxOUTFS
xRSET
0.1F
REFIO
IxREF
AVSS
FSADJx
VBG
1.0V
+
–
Figure 96. Internal Reference Configuration
REFIO serves as either an input or an output, depending on
whether the internal or an external reference is used. Table 17
summarizes the reference operation.
Table 17. Reference Operation
Reference Mode
REFIO Pin
Register Setting
Internal
Connect 0.1 F
capacitor
Register 0x01, Bit 0 = 0
(default)
External
Apply external
reference
Register 0x01, Bit 0 = 1
(for power saving)
An external reference can be used in applications requiring tighter
gain tolerances or lower temperature drift. In addition, a variable
external voltage reference can be used to implement a method
for gain control of the DAC output.
Recommendations When Using an External Reference
Apply the external reference to the REFIO pin. The internal
reference can be directly overdriven by the external reference,
or the internal reference can be powered down to save power
consumption.
The external 0.1 F compensation capacitor on REFIO is not
required unless specified by the external voltage reference
manufacturer. The input impedance of REFIO is 10 kΩ when
the internal reference is powered up and 1 MΩ when it is
powered down.
REFERENCE CONTROL AMPLIFIER
The AD9114/AD9115/AD9116/AD9117 contains a control
amplifier that regulates the full-scale output current, IxOUTFS.
The control amplifier is configured as a V-I converter, as shown
the VREFIO and an external resistor, xRSET, as stated in Equation 4 (see
segmented current sources with the proper scale factor to set
section).
The control amplifier allows a 10:1 adjustment span of IxOUTFS
from 2 mA to 20 mA by setting IxREF between 62.5 A and 625 A
(xRSET between 1.6 k and 16 k). When using a resistor larger
than 4 k, split the resistor with 4 k plus the additional
resistance needed, for example, 16 k made of a 4 k + 12 k
combination, and add a 1 F capacitor from 4 k to ground.
The wide adjustment span of IxOUTFS provides several benefits.
The first relates directly to the power dissipation of the
AD9114/AD9115/AD9116/AD9117, which is proportional to
benefit relates to the ability to adjust the output over a 8 dB
range with 0.25 dB steps, which is useful for controlling the
transmitted power. The small signal bandwidth of the reference
control amplifier is approximately 500 kHz. This allows the
device to be used for low frequency, small signal multiplying
applications.
DAC TRANSFER FUNCTION
The AD9114/AD9115/AD9116/AD9117 provides two differential
current outputs, IOUTP/IOUTN and QOUTP/ QOUTN. IOUTP
and QOUTP provide a near full-scale current output, IxOUTFS,
when all bits are high (that is, DAC CODE = 2N 1, where N = 8,
10, 12, or 14 for the AD9114, AD9115, AD9116, and AD9117,
respectively), while IOUTN and QOUTN, the complementary
outputs, provide no current. The current outputs appearing at the
positive DAC outputs, IOUTP and QOUTP, and at the negative
DAC outputs, IOUTN and QOUTN, are a function of both the
input code and IxOUTFS and can be expressed as follows:
IOUTP = (IDAC CODE/2N) × IIOUTFS
(1)
QOUTP = (QDAC CODE/2N) × IQOUTFS
IOUTN = ((2N 1) IDAC CODE)/2N × IIOUTFS
(2)
QOUTN = ((2N 1) QDAC CODE)/2N × IQOUTFS
where:
IDAC CODE and QDAC CODE = 0 to 2N 1 (that is, decimal
representation).
IIOUTFS and IQOUTFS are functions of the reference currents, IIREF
and IQREF, respectively, which are nominally set by a reference
voltage, VREFIO, and external resistors, IRSET and QRSET, respectively.
IIOUTFS and IQOUTFS can be expressed as follows:
IIOUTFS = 32 × IIREF
(3)
IQOUTFS = 32 × IQREF
相關PDF資料 |
PDF描述 |
|---|---|
| VE-26F-MW-B1 | CONVERTER MOD DC/DC 72V 100W |
| AD9762ARURL7 | IC DAC 12BIT 100KSPS 28-TSSOP |
| AD9762ARRL | IC DAC 12BIT 100KSPS 28-SOIC |
| AD7545AKRZ-REEL7 | IC DAC 12BIT W/BUFF MULT 20SOIC |
| VE-264-MW-B1 | CONVERTER MOD DC/DC 48V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9115-DPG2-EBZ | 功能描述:IC DAC DUAL 10BIT LO PWR 40LFCSP RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9115-EBZ | 制造商:Analog Devices 功能描述:DUAL 10 BIT LOW POWER CONVERTER - Boxed Product (Development Kits) |
| AD9116 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, 8-/10-/12-/14-Bit Low Power Digital-to-Analog Converters |
| AD9116BCPZ | 功能描述:IC DAC DUAL 12BIT LO PWR 40LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD9116BCPZRL7 | 功能描述:IC DAC DUAL 12BIT LO PWR 40LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。