- 您現在的位置：買賣IC網 > PDF目錄373957 > AD9042DPCB (Analog Devices, Inc.) 12-Bit, 41 MSPS Monolithic A/D Converter PDF資料下載
參數資料
| 型號： | AD9042DPCB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 12-Bit, 41 MSPS Monolithic A/D Converter |
| 中文描述： | 12位，41 MSPS的單片機的A / D轉換器 |
| 文件頁數： | 12/24頁 |
| 文件大小： | 488K |
| 代理商： | AD9042DPCB |
AD9042
–12–
REV. A
If no T T L source is available, a clean sine wave may be
substituted. In the case of the sine source, the matching net-
work is shown below. Since the matching transformer specified
is a 1:1 impedance ratio, R, the load resistor should be selected
to match the source impedance. T he input impedance of the
AD9042 is negligible in most cases.
ENCODE
ENCODE
AD9042
R
T1-1T
SINE
SOURCE
Figure 30. Sine Source – Differential Encode
If a low jitter ECL clock is available, another option is to ac-
couple a differential ECL signal to the encode input pins as
shown below. T he capacitors shown here should be chip
capacitors but do not need to be of the low inductance variety.
ENCODE
ENCODE
AD9042
ECL
GATE
0.1μF
0.1μF
–V
S
510
510
Figure 31. Differential ECL for Encode
As a final alternative, the ECL gate may be replaced by an ECL
comparator. T he input to the comparator could then be a logic
signal or a sine signal.
ENCODE
ENCODE
AD9042
0.1μF
0.1μF
–V
S
50
AD96687 (1/2)
510
510
Figure 32. ECL Comparator for Encode
Care should be taken not to overdrive the encode input pin
when ac coupled. Although the input circuitry is electrically
protected from over or under voltage conditions, improper
circuit operations may result from overdriving the encode input
pins.
Driving the Analog Input
Because the AD9042 operates off of a single +5 V supply, the
analog input range is offset from ground by 2.4 volts. T he
analog input, AIN, is an operational amplifier configured in an
inverting mode (ref. Equivalent Circuits: Analog Input Stage).
V
OFFSET
is the noninverting input which is normally tied
through a 50 ohm resistor to V
REF
(ref. Equivalent Circuits:
2.4 V Reference). Since the operational amplifier forces its
inputs to the same voltage, the inverting input is also at 2.4 volts.
T herefore, the analog input has a T hevenin equivalent of 250 ohms
in series with a 2.4 volt source. It is strongly recommended
that the AD9042’s internal voltage reference be used for the
amplifier offset; this reference is designed to track internal cir-
cuit shifts over temperature.
AD9042
250
250
+2.4V
REFERENCE
AIN
THROUGH
50 OHMS
TIED TO
V
REF
V
OFFSET
50
0.1μF
Figure 33. Analog Input Offset by +2.4 V Reference
Although the AD9042 may be used in many applications, it was
specifically designed for communications systems which must
digitize wide signal bandwidths. As such, the analog input was
designed to be ac-coupled. Since most communications products
do not down-convert to dc, this should not pose a problem. One
example of a typical analog input circuit is shown below. In this
application, the analog input is coupled with a high quality chip
capacitor, the value of which can be chosen to provide a low
frequency cutoff that is consistent with the signal being
sampled; in most cases, a 0.1
μ
F chip capacitor will work well.
AD9042
0.1μF
50
ANALOG
SIGNAL
SOURCE
R
T
0.1μF
AIN
V
OFFSET
V
REF
Figure 34. AC-Coupled Analog Input Signal
Another option for ac-coupling is a transformer. T he imped-
ance ratio and frequency characteristics of the transformer are
determined by examining the characteristics of the input signal
source (transformer primary connection), and the AD9042 in-
put characteristics (transformer secondary connection). “R
T
”
should be chosen to satisfy termination requirements of the
source, given the transformer turns ratio. A blocking capacitor
is required to prevent AD9042 dc bias currents from flowing
through the transformer.
BPF
R
T
XFMR
LO
ANALOG
SIGNAL
SOURCE
0.1μF
50
0.1μF
AD9042
AIN
V
OFFSET
V
REF
Figure 35. Transformer-Coupled Analog Input Signal
When calculating the proper termination resistor, note that the
external load resistor is in parallel with the AD9042 analog
input resistance, 250 ohms. T he external resistor value can be
calculated from the following equation:
R
T
=
1
1
Z
1
250
where
Z
is desired impedance.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9042D | 12-Bit, 41 MSPS Monolithic A/D Converter |
| AD9042ST | 12-Bit, 41 MSPS Monolithic A/D Converter |
| AD9042STPCB | 12-Bit, 41 MSPS Monolithic A/D Converter |
| AD9042AD | 12-Bit, 41 MSPS Monolithic A/D Converter |
| AD9042AST | 12-Bit, 41 MSPS Monolithic A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9042ST | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 41 MSPS Monolithic A/D Converter |
| AD9042ST/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 41 MSPS Monolithic A/D Converter |
| AD9042STPCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 41 MSPS Monolithic A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。