- 您現在的位置：買賣IC網 > PDF目錄8695 > AD8804ARZ-REEL (Analog Devices Inc)IC DAC 8BIT 12CH W/SD 20SOIC PDF資料下載
參數資料
| 型號： | AD8804ARZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 8BIT 12CH W/SD 20SOIC |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1,000 |
| 系列： | TrimDAC® |
| 設置時間： | 600ns |
| 位數： | 8 |
| 數據接口： | 串行 |
| 轉換器數目： | 12 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 60µW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 12 電壓，單極 |
| 采樣率（每秒）： | 1.7M |
AD8802/AD8804
REV. 0
–13–
*
LDAA
$0000
Hi-byte data loaded from memory
STAA
SDI1
SDI1 = data in location 0000H
*
* Enter Contents of SDI2 Data Register
*
LDAA
$0001
Low-byte data loaded from memory
STAA
SDI2
SDI2 = Data in location 0001H
*
LDX
#SDI1
Stack pointer at 1st byte to send via SDI
LDY
#$1000
Stack pointer at on-chip registers
*
* Reset AD8802 to one-half scale (AD8804 does not have a Reset input)
*
BCLR
PORTC,Y $02
Assert /RS
BSET
PORTC,Y $02
De-Assert /RS
*
* Get AD8802/04 ready for data input
*
BCLR
PORTD,Y $02
Assert /CS
*
TFRLP
LDAA
0,X
Get a byte to transfer for SPI
STAA
SPDR
Write SDI data reg to start xfer
*
WAIT
LDAA
SPSR
Loop to wait for SPIF
BPL
WAIT
SPIF is the MSB of SPSR
*
INX
Increment counter to next byte for xfer
CPX
#SDI2+1
Are we done yet ?
BNE
TFRLP
If not, xfer the second byte
*
* Update AD8802 output
*
BSET
PORTD,Y $20
Latch register & update AD8802
*
PULA
When done, restore registers X, Y & A
PULY
PULX
RTS
** Return to Main Program **
Listing 3. AD8802/AD8804 to MC68HC11 Interface Program Source Code
An Intelligent Temperature Control System—Interfacing the
8051
C with the AD8802/AD8804 and TMP14
Connecting the 80CL51
C, or any modern microcontroller,
with the TMP14 and AD8802/AD8804 yields a powerful tem-
perature control tool, as shown in Figure 27. For example, the
80CL51
C controls the TrimDACs allowing the user to auto-
matically set the temperature setpoints voltages of the TMP14
via computer or touch pad, while the TMP14 senses the tem-
perature and outputs four open-collector trip-points. Feeding
these trip-point outputs back to the 80CL51
C allow it to sense
whether or not a setpoint has been exceeded. Additional
80CL51
C port pins or TMP14 trip-point outputs may then
be used to change fan speed (i.e., high, medium, low, off), or
increase/decrease the power level to a heater. (Please refer to the
TMP14 data sheet for more applications information.)
The CS (Chip Select) on the AD8802/AD8804 makes applica-
tions that call for large temperature sensor arrays possible. In
addition, the 12 channels of the AD8802/AD8804 allow inde-
pendent setpoint control for all four trip-point outputs on up to
three TMP14 temperature sensors. For example, assume that
the 80CL51
C has eight free port pins available after all user
interface lines, interrupts, and the serial port lines have been
assigned. The eight port pins may be used as chip selects, in
which case an array of eight AD8802/AD8804s controlling
twenty-four TMP14 sensors is possible.
The AD8802/AD8804 and TMP14 are also ideal choices for
low power applications. These devices have power shutdown
modes and operate on a single 5 Volt supply. When their shut-
down modes are activated current consumption is reduced to
less than 35
A. However, at high operating frequencies
(12 MHz) the 80CL51 consumes far more energy (18 mA typ)
than the AD8802/AD8804 and TMP14 combined. Therefore,
to achieve a low power design the 80CL51 should operate at its
lowest possible frequency or be placed in its power-down mode
at the end of each instruction sequence.
To use the power-down mode of the 80CL51
C set PCON.1
as the last instruction executed prior to going into the power-
down mode. If INT2 and INT9 are enabled, the 80CL51
C
can be awakened from power-down mode with external inter-
rupts. As shown in Figure 28, the TLC555 outputs a pulse
every few seconds providing the interrupt to restart the 80CL51
C which then samples the user input pins, the outputs of the
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BNB-MV-F1 | CONVERTER MOD DC/DC 95V 150W |
| V300A12H400BG | CONVERTER MOD DC/DC 12V 400W |
| AD5317BRUZ-REEL7 | IC DAC 10BIT QUAD W/BUFF 16TSSOP |
| VI-BN4-MV-F1 | CONVERTER MOD DC/DC 48V 150W |
| VI-BN3-MV-F2 | CONVERTER MOD DC/DC 24V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD880AJR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD880JR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD883B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Programmable Gain Instrumentation Amplifier |
| AD883B2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Drift, Low Power Instrumentation Amplifier |
| AD883B3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, Low Noise, Wideband Variable Gain Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。