參數資料
型號： AD8529ARMZ-REEL
廠商： Analog Devices Inc
文件頁數： 4/16頁
文件大小： 0K
描述： IC OPAMP GP R-R 8MHZ DUAL 8MSOP
標準包裝： 1
放大器類型： 通用
電路數： 2
輸出類型： 滿擺幅
轉換速率： 2.9 V/µs
增益帶寬積： 8MHz
電流 - 輸入偏壓： 300nA
電壓 - 輸入偏移： 600µV
電流 - 電源： 600µA
電流 - 輸出 / 通道： 25mA
電壓 - 電源，單路/雙路(±)： 2.7 V ~ 12 V，±1.35 V ~ 6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 標準包裝
其它名稱： AD8529ARMZ-REELDKR
AD8519/AD8529
Rev. D | Page 12 of 16
APPLICATIONS INFORMATION
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD8519/AD8529 is limited by the associated rise in junction
temperature. The maximum safe junction temperature is 150°C
for these plastic packages. If this maximum is momentarily
exceeded, proper circuit operation is restored as soon as the
die temperature is reduced. Operating the product in an
overheated condition for an extended period can result in
permanent damage to the device.
PRECISION FULL-WAVE RECTIFIER
Slew rate is probably the most underestimated parameter when
designing a precision rectifier. Yet without a good slew rate,
large glitches are generated during the period when both diodes
are off.
The operation of the basic circuit (shown in Figure 23) should
be examined before considering the slew rate further. U1 is set
up to have two states of operation. D1 and D2 diodes switch the
output between the two states. State one is an inverter with a
gain of +1, and state two is a simple unity gain buffer where the
output is equal to the value of the virtual ground. The virtual
ground is the potential present at the noninverting node of the
U1. State one is active when VIN is larger than the virtual
ground. D2 is on in this condition. If VIN drops below virtual
ground, D2 turns off and D1 turns on. This causes the output of
U1 to simply buffer the virtual ground and this configuration is
state two. Therefore, the function of U1, which results from
these two states of operation, is a half-wave inverter. The U2
function takes the inverted half wave at a gain of two and sums
it into the original VIN wave, which outputs a rectified full wave.
0
2
1
<
=
IN
OUT
V
This type of rectifier can be very precise if the following
electrical parameters are adhered to:
All passive components should be of tight tolerance, 1% for
resistors and 5% for capacitors.
If the application circuit requires high impedance (that is,
direct sensor interface), then an FET amplifier is a better
choice than the AD8519.
An amp such as the AD8519, which has a great slew rate
specification, yields the best result because the circuit
involves switching.
AD8519
U2
U1
VIRTUAL GROUND =
2
NODE A
VOUT
VCC
VIN
R1
10k
R4
10k
R2
10k
R3
4.99k
R5
10k
D2
1N914
D1
1N914
R7
3.32k
R6
5k
0175
6-
023
Figure 23. Precision Full-Wave Rectifier
Switching glitches are caused when D1 and D2 are both
momentarily off. This condition occurs every time the input
signal is equal to the virtual ground potential. When this
condition occurs, the U1 stage is taken out of the VOUT equation
and VOUT is equal to VIN × R5 × (R4 || R1 + R2 + R3). Note that
Node A should be VIN inverted or virtual ground, but in this
condition, Node A is simply tracking VIN. Given a sine wave
input centered around virtual ground, glitches are generated
at the sharp negative peaks of the rectified sine wave. If the
glitches are hard to notice on an oscilloscope, raise the fre-
quency of the sine wave until they become apparent. The size
of the glitches is proportional to the input frequency, the diode
turn-on potential (0.2 V or 0.65 V), and the slew rate of the op amp.
R6 and R7 are both necessary to limit the amount of bias
current related voltage offset. Unfortunately, there is no perfect
value for R6 because the impedance at the inverting node is
altered as D1 and D2 switch. Therefore, there is also some
unresolved bias current related offset. To minimize this offset,
use lower value resistors or choose an FET amplifier if the
optimized offset is still intolerable.
The AD8519 offers a unique combination of speed vs. power
ratio at 2.7 V single supply, small size (SC70 and SOT-23), and low
noise that makes it an ideal choice for most high volume and
high precision rectifier circuits.
相關PDF資料
PDF描述
F1206A1R00FWTR FUSE 1.00A 32V FAST THIN 1206
TSW-106-08-S-S CONN HEADER 6POS .100" SGL GOLD
1.5KE250A TVS 1500W 250V UNIDIRECT AXIAL
F1206A1R00FSTR FUSE 1.00A 32V FAST THIN 1206
F1206A0R75FWTR FUSE 0.75A 32V FAST THIN 1206
相關代理商/技術參數
參數描述
AD8529AR-REEL 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R O/P
AD8529ARZ 功能描述:IC OPAMP GP R-R 8MHZ DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT
AD8529ARZ-REEL 功能描述:IC OPAMP GP R-R 8MHZ DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR)
AD8531 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, 250 mA Output Single-Supply Amplifiers
AD8531_08 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, 250 mA Output, Single-Supply Amplifiers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*