- 您現在的位置：買賣IC網 > PDF目錄5950 > AD8476BRMZ-RL (Analog Devices Inc)IC AMP DIFF ADC DVR 8MSOP PDF資料下載
參數資料
| 型號： | AD8476BRMZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/24頁 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF ADC DVR 8MSOP |
| 標準包裝： | 3,000 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 輸出類型： | 差分，滿擺幅 |
| 轉換速率： | 10 V/µs |
| -3db帶寬： | 5MHz |
| 電流 - 電源： | 330µA |
| 電流 - 輸出 / 通道： | 35mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 18 V，±1.5 V ~ 9 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
AD8476
Data Sheet
Rev. B | Page 18 of 24
The AD8476 integrated resistors are precision wafer-laser-
trimmed to guarantee a minimum CMRR of 90 dB (32 μV/V),
and gain error of less that 0.02%. To achieve equivalent precision
and performance using a discrete solution, resistors must be
matched to 0.01% or better.
INPUT VOLTAGE RANGE
The AD8476 can measure input voltages as large as the supply
rails. The internal gain and feedback resistors form a divider,
which reduces the input voltage seen by the internal input
nodes of the amplifier. The largest voltage that can be measured
properly is constrained by the output range of the amplifier and
the capability of the amplifier’s internal summing nodes. This
voltage is defined by the input voltage, and the ratio between the
feedback and the gain resistors.
Figure 53 shows the voltage at the internal summing nodes of
the amplifier, defined by the input voltage and internal resistor
network. If VN is grounded, the expression shown reduces to
+
=
P
MINUS
PLUS
V
RG
RF
VOCM
RG
RF
RG
V
2
1
The internal amplifier of the AD8476 has rail-to-rail inputs.
To obtain accurate measurements with minimal distortion, the
voltage at the internal inputs of the amplifier must stay below
+VS 1 V and above VS.
The AD8476 provides overvoltage protection for excessive input
voltages beyond the supply rails. Integrated ESD protection diodes
and VS 18 V.
DRIVING THE AD8476
Care should be taken to drive the AD8476 with a low
impedance source: for example, another amplifier. Source
resistance can unbalance the resistor ratios and, therefore,
significantly degrade the gain accuracy and common-mode
rejection of the AD8476. For the best performance, source
impedance to the AD8476 input terminals should be kept
below 0.1 Ω. Refer to the DC Precision section for details on
the critical role of resistor ratios in the precision of the AD8476.
POWER SUPPLIES
The AD8476 operates over a wide range of supply voltages. It
can be powered on a single supply as low as 3 V and as high as
18 V. The AD8476 can also operate on dual supplies from
±1.5 V to ±9 V
A stable dc voltage should be used to power the AD8476. Note
that noise on the supply pins can adversely affect performance.
For more information, see the PSRR performance curve in
Place a bypass capacitor of 0.1 μF between each supply pin and
ground, as close as possible to each supply pin. Use a tantalum
capacitor of 10 μF between each supply and ground. It can be
farther away from the supply pins and, typically, it can be
shared by other precision integrated circuits.
RF
RG
VON
VOP
VOCM
VP
VN
VN
RF + RG
RF
VP VN
RG
RF
VOCM
RF + RG
RG
+
2
1
10195-
060
Figure 53. Voltages at the Internal Op Amp Inputs of the AD8476
相關PDF資料 |
PDF描述 |
|---|---|
| PEC20DBDN | CONN HEADER .100 DUAL R/A 40POS |
| PMT809004F | GP THREE ELEMENTS S.A. 90V T/H |
| 5TT 2-R | FUSE SLOW 250VAC 2A 5X20 |
| RW1S0BAR015FT | RES POWER .015 OHM 1W 1% SMT |
| SL1021B500RG | GAS TUBE GDT 500V 20KA RAD+FS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8476-EVALZ | 功能描述:BOARD EVAL FOR AD8476 RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8479 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Very High Common-Mode Voltage Precision Difference Amplifier |
| AD8479ARZ | 功能描述:差分放大器 Very High Common Mode VTG Prec RoHS:否 制造商:Analog Devices 通道數量:1 Channel 帶寬:900 MHz 可用增益調整:5.6 dB to 20 dB 輸入補償電壓:1 mV at 5 V 共模抑制比（最小值）:67 dB 工作電源電壓:11 V 電源電流:28 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| AD8479ARZ-RL | 功能描述:差分放大器 Very High Common Mode VTG Prec RoHS:否 制造商:Analog Devices 通道數量:1 Channel 帶寬:900 MHz 可用增益調整:5.6 dB to 20 dB 輸入補償電壓:1 mV at 5 V 共模抑制比（最小值）:67 dB 工作電源電壓:11 V 電源電流:28 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| AD8479BRZ | 功能描述:差分放大器 Very High Common Mode VTG Prec RoHS:否 制造商:Analog Devices 通道數量:1 Channel 帶寬:900 MHz 可用增益調整:5.6 dB to 20 dB 輸入補償電壓:1 mV at 5 V 共模抑制比（最小值）:67 dB 工作電源電壓:11 V 電源電流:28 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。