- 您現在的位置：買賣IC網 > PDF目錄8531 > AD8421BRZ-R7 (Analog Devices Inc)IC OPAMP INST 10MHZ LP LN 8MSOP PDF資料下載
參數資料
| 型號： | AD8421BRZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP INST 10MHZ LP LN 8MSOP |
| 標準包裝： | 1,000 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 轉換速率： | 35 V/µs |
| -3db帶寬： | 10MHz |
| 電流 - 輸入偏壓： | 100pA |
| 電壓 - 輸入偏移： | 25µV |
| 電流 - 電源： | 2mA |
| 電流 - 輸出 / 通道： | 65mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 36 V，±2.5 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOICN |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Data Sheet
AD8421
Rev. 0 | Page 23 of 28
a current of 40 mA at room temperature for at least a day. This
time is cumulative over the life of the device. If long periods of
overvoltage are expected, the use of an external protection method
is recommended. Under extreme input conditions, the output
of the amplifier may invert.
RADIO FREQUENCY INTERFERENCE (RFI)
RF rectification is often a problem when amplifiers are used in
applications that have strong RF signals. The problem is intensified
if long leads or PCB traces are required to connect the amplifier
to the signal source. The disturbance can appear as a dc offset
voltage or a train of pulses.
High frequency signals can be filtered with a low-pass filter
network at the input of the instrumentation amplifier, as shown
in Figure 68.
R
AD8421
+VS
+IN
–IN
0.1F
10F
0.1F
REF
VOUT
–VS
CD
10nF
CC
1nF
CC
1nF
33
1
012
3-
067
L*
*CHIP FERRITE BEAD.
Figure 68. RFI Suppression
The choice of resistor and capacitor values depends on the
desired trade-off between noise, input impedance at high
frequencies, CMRR, signal bandwidth, and RFI immunity. An
RC network limits both the differential and common-mode
bandwidth, as shown in the following equations:
)
2
(
π
2
1
C
D
DIFF
C
R
uency
FilterFreq
+
=
C
CM
RC
uency
FilterFreq
π
2
1
=
where CD ≥ 10 CC.
CD affects the differential signal, and CC affects the common-
mode signal. A mismatch between R × CC at the positive input
and R × CC at the negative input degrades the CMRR of the
larger than CC, the effect of the mismatch is reduced and CMRR
performance is improved near the cutoff frequencies.
To achieve low noise and sufficient RFI filtering, the use of chip
ferrite beads is recommended. Ferrite beads increase their impe-
dance with frequency, thus leaving the signal of interest unaffected
while preventing RF interference to reach the amplifier. They also
help to eliminate the need for large resistor values in the filter,
thus minimizing the system’s input-referred noise. The selection
of the appropriate ferrite bead and capacitor values is a function
of the interference frequency, input lead length, and RF power.
For best results, place the RFI filter network as close as possible
to the amplifier. Layout is critical to ensure that RF signals are
not picked up on the traces after the filter. If RF interference is
too strong to be filtered sufficiently, shielding is recommended.
The resistors used for the RFI filter can be the same as those used
for input protection.
CALCULATING THE NOISE OF THE INPUT STAGE
The total noise of the amplifier front end depends on much more
than the 3.2 nV/√Hz specification of this data sheet. The three
main contributors to noise are: the source resistance, the voltage
noise of the instrumentation amplifier, and the current noise of
the instrumentation amplifier.
In the following calculations, noise is referred to the input (RTI).
In other words, all sources of noise are calculated as if the source
appeared at the amplifier input. To calculate the noise referred
to the amplifier output (RTO), multiply the RTI noise by the
gain of the instru-mentation amplifier.
Source Resistance Noise
Any sensor connected to the AD8421 has some output resistance.
There may also be resistance placed in series with inputs for pro-
tection from either overvoltage or radio frequency interference.
This combined resistance is labeled R1 and R2 in Figure 69. Any
resistor, no matter how well made, has an intrinsic level of noise.
This noise is proportional to the square root of the resistor value.
At room temperature, the value is approximately equal to
4 nV/√Hz × √(resistor value in kΩ).
R2
RG
R1
SENSOR
AD8421
1
012
3-
0
65
Figure 69. Source Resistance from Sensor and Protection Resistors
For example, assume that the combined sensor and protection
resistance is 4 kΩ on the positive input and 1 kΩ on the negative
input. Then the total noise from the input resistance is
(
) (
)
=
+
=
×
+
×
16
64
1
4
2
8.9 nV/√Hz
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J1K-MW-S | CONVERTER MOD DC/DC 40V 100W |
| VE-J1J-MW-S | CONVERTER MOD DC/DC 36V 100W |
| VE-J12-MW-S | CONVERTER MOD DC/DC 15V 100W |
| VE-J11-MW-S | CONVERTER MOD DC/DC 12V 100W |
| VE-BWF-MX-S | CONVERTER MOD DC/DC 72V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8421BRZ-RL | 功能描述:IC OPAMP INST 10MHZ LP LN 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:2.1 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:2000µV 電流 - 電源:750µA 電流 - 輸出 / 通道:16mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 16 V，±1.35 V ~ 8 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-10529-1 |
| AD8421TRMZ-EP | 制造商:Analog Devices 功能描述:3NV/VHZNOISEPRECISIONINAMP - Rail/Tube 制造商:Analog Devices 功能描述:IC OPAMP INSTR 10MHZ 8MSOP 制造商:Analog Devices 功能描述:3nV/vHz noise Precision InAmp |
| AD8421TRMZ-EP-R7 | 制造商:Analog Devices 功能描述:3NV/VHZNOISEPRECISIONINAMP - Tape and Reel 制造商:Analog Devices 功能描述:IC OPAMP INSTR 10MHZ 8MSOP 制造商:Analog Devices 功能描述:3nV/vHz noise Precision InAmp |
| AD8422 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance, Low Power, Rail-to-Rail Precision Instrumentation Amplifier |
| AD8422ARMZ | 制造商:Analog Devices 功能描述:HIGHPERFORMANCEINAMP - Rail/Tube 制造商:Analog Devices 功能描述:IC OPAMP INSTR 2.2MHZ RRO 8MSOP 制造商:Analog Devices 功能描述:INSTRUMENT AMP 2.2MHZ 80DB 8 MSOP 制造商:Analog Devices 功能描述:INSTRUMENT AMP, 2.2MHZ, 80DB, 8 MSOP 制造商:Analog Devices 功能描述:INSTRUMENT AMP, 2.2MHZ, 80DB, 8 MSOP, No. of Amplifiers:1, Input Offset Voltage:70V, Bandwidth:2.2MHz, Supply Voltage Range:3.5V to 36V, Amplifier Case Style:MSOP, No. of Pins:8, Amplifier Output:Rail to Rail, CMRR:86dB, Slew 制造商:Analog Devices 功能描述:High Performance InAmp 制造商:Analog Devices 功能描述:INSTR-AMPLIFIER, 2.2MHZ, 86DB, MSOP-8, No. of Amplifiers:1, Input Offset Voltage:70V, Bandwidth:2.2MHz, Supply Voltage Range:3.6V to 36V, Amplifier Case Style:MSOP, No. of Pins:8, Amplifier Output:Rail to Rail, CMRR:86dB 制造商:Analog Devices 功能描述:AMPLIFIER - SPECIAL PURPOSE |
發布緊急采購，3分鐘左右您將得到回復。