參數資料
型號： AD8293G160ARJZ-R2
廠商： Analog Devices Inc
文件頁數： 4/16頁
文件大小： 0K
描述： IC AMP INST R-R LDRIFT SOT23-8
標準包裝： 250
放大器類型： 儀表
電路數： 1
輸出類型： 滿擺幅
-3db帶寬： 500Hz
電流 - 輸入偏壓： 400pA
電壓 - 輸入偏移： 9µV
電流 - 電源： 1mA
電流 - 輸出 / 通道： 35mA
電壓 - 電源，單路/雙路(±)： 1.8 V ~ 5.5 V，±0.9 V ~ 2.75 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： SOT-23-8
供應商設備封裝： SOT-23-8
包裝： 帶卷 (TR)
AD8293G80/AD8293G160
Rev. 0 | Page 12 of 16
he addition of another single pole of 700 Hz on the output
hs
C3 (nF)
T
(from the secondary filter in Figure 18) is required for bandwidt
greater than 10 Hz. These two filters, together, produce an overall
bandwidth of 500 Hz. The internal resistors, R2 and R3, have an
absolute tolerance of 20%. Table 8 lists the standard capacitors
needed to create a filter with an overall bandwidth of 500 Hz.
Table 8. Standard Capacitors Used to Form a Filter with an
Overall Bandwidth of 500 Hz
Model
C2 (pF)
AD8293G80
1300
39
AD8293G160
680
39
For applications with low bandwi ths (<10 Hz), only the primary
H
use two synchronized clocks
ncies can be observed at
d
filter is required. In such an event, the high frequency noise
from the auto-zero amplifier (output amplifier) is not filtered
before the following stage.
CLOCK FEEDTHROUG
The AD8293G80/AD8293G160
to perform the autocorrection. The input voltage-to-current
amplifiers are corrected at 60 kHz.
Trace amounts of these clock freque
the OUT pin. The amount of visible correction feedthrough
is dependent on the values of the filters set by R2/C2. Use
ADC OUT to create a filter using R3/C3 to further reduce
correction feedthrough as described in the Output Filtering
POWER SUPPLY BYPASSING
The AD8293G80/AD8293G160 use internally generated clock
signals to perform autocorrection. As a result, proper bypassing
is necessary to achieve optimum performance. Inadequate or
improper bypassing of the supply lines can lead to excessive
noise and offset voltage.
A 0.1 μF surface-mount capacitor should be connected between
the supply lines. This capacitor is necessary to minimize ripple
from the correction clocks inside the IC. For dual-supply operation,
a 0.1 μF (ceramic) surface-mount capacitor should be connected
from each supply pin to GND.
For single-supply operation, a 0.1 μF surface-mount capacitor
should be connected from the supply line to GND.
All bypass capacitors should be positioned as close to the DUT
supply pins as possible, especially the bypass capacitor between
the supplies. Placement of the bypass capacitor on the back of
the board directly under the DUT is preferred.
INPUT OVERVOLTAGE PROTECTION
All terminals of the AD8293G80/AD8293G160 are protected
against ESD. In the case of a dc overload voltage beyond either
supply, a large current would flow directly through the ESD
protection diodes. If such a condition can occur, an external resistor
should be used in series with the inputs to limit current for voltages
beyond the supply rails. The AD8293G80/AD8293G160 can safely
handle 5 mA of continuous current, resulting in an external
resistor selection of
REXT = (VIN VS)/5 mA
1
8
7
5
6
4
ADC OUT
FILT
+VS
I
1.8V
–IN
+IN
R1
4k
R2
160k
RSHUNT
R3
5k
+3.3V
10F
0.1F
C3
39nF
OUT
C2
1.3nF
07
45
1-
0
23
AD8293G80
REF
GND
3
2
IN-AMP
ADC
REF
LOAD
DC-DC
+5V
0.1F
Figure 21. Measuring Current Through a Shunt Resistor (Filter Is Set to 500 Hz)
相關PDF資料
PDF描述
LT6000IDCB#TRPBF IC OP AMP R-R 1.8V 6-DFN
AGC-V-1/10-R FUSE 1/10A 250V GLS FST AXIAL UL
MDL-1/16-R FUSE 1/16A 250V T-LAG GLASS
MDL-1/10-R FUSE 1/10A 250V T-LAG GLASS
31159 CONN RING TONGUE 22-16AWG #6
相關代理商/技術參數
參數描述
AD8293G160ARJZ-R7 功能描述:IC AMP INST R-R LDRIFT SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT
AD8293G160ARJZ-RL 功能描述:IC AMP INST R-R LDRIFT SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件
AD8293G160BRJZ-R2 功能描述:IC AMP INST R-R LDRIFT SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
AD8293G160BRJZ-R7 功能描述:IC AMP INST R-R LDRIFT SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR)
AD8293G160BRJZ-RL 功能描述:IC AMP INST R-R LDRIFT SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*