- 您現在的位置：買賣IC網 > PDF目錄375243 > AD8206YR-REEL (ANALOG DEVICES INC) Single-Supply 42 V System Difference Amplifier PDF資料下載
參數資料
| 型號： | AD8206YR-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Single-Supply 42 V System Difference Amplifier |
| 中文描述： | OP-AMP, 4500 uV OFFSET-MAX, PDSO8 |
| 封裝： | MS-012AA, SOIC-8 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 260K |
| 代理商： | AD8206YR-REEL |
Preliminary Technical Data
AD8206
OUTPUT OFFSET ADJUSTMENT
The output of the AD8206 can be adjusted for unidirectional or
bidirectional operation.
Rev. PrA | Page 9 of 12
UNIDIRECTIONAL OPERATION
Unidirectional operation allows the AD8206 to measure cur-
rents through a resistive shunt in one direction. The basic
modes for unidirectional operation are ground referenced
output mode and V+ referenced output mode.
In the case of unidirectional operation, the output could be set
at the negative rail (near ground) or at the positive rail (near
V+) when the differential input is 0 V. The output moves to the
opposite rail when a correct polarity differential input voltage is
applied. In this case, full scale is approximately 250 mV. The
required polarity of the differential input depends on the output
voltage setting. If the output is set at the positive rail, the input
polarity needs to be negative to move the output down. If the
output is set at ground, the polarity is positive to move the
output up.
GROUND REFERENCED OUTPUT
When using the AD8206 in this mode, both reference inputs are
tied to ground, which causes the output to sit at the negative rail
when there are zero differential volts at the input (see Figure 14).
0
AD8206
+IN
–IN
NC
NC = NO CONNECT
GND
V+
OUT
V
REF
1
V
REF
2
Figure 14. Ground Referenced Output
Table 4. V+ = 5 V
V
IN
(Referred to IN)
0 V
250 mV
V
O
0.05 V
4.8 V
V+ REFERENCED OUTPUT
This mode is set when both reference pins are tied to the posi-
tive supply. It is typically used when the diagnostic scheme
requires detection of the amplifier and the wiring before power
is applied to the load (see Figure 15).
0
AD8206
+IN
–IN
NC
NC = NO CONNECT
GND
V+
OUT
V
REF
1
V
REF
2
Figure 15. V+ Referenced Output
Table 5. V+ = 5 V
V
IN
(Referred to IN)
0 V
250 mV
BIDIRECTIONAL OPERATION
Bidirectional operation allows the AD8206 to measure currents
through a resistive shunt in two directions.
V
O
4.8 V
0.05 V
In this case, the output is set anywhere within the output range.
Typically, it is set at half-scale for equal range in both directions.
In some cases, however, it is set at a voltage other than half-scale
when the bidirectional current is nonsymmetrical.
Table 6. V+ = 5 V, V
O
= 2.5 with V
IN
= 0 V
V
IN
(Referred to IN)
+100 mV
100 mV
Adjusting the output is accomplished by applying voltage(s) to
the reference inputs.
V
O
4.5 V
0.5 V
V
REF
1 and V
REF
2 are tied to internal resistors that connect to an
internal offset node. There is no operational difference between
the pins.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8206YR-REEL7 | Single-Supply 42 V System Difference Amplifier |
| AD823 | Dual, 16 MHz, Rail-to-Rail FET Input Amplifier(16MHz,滿幅度,場效應晶體管輸入雙運放) |
| AD8300AN | +3 Volt, Serial Input Complete 12-Bit DAC |
| AD8300AR | +3 Volt, Serial Input Complete 12-Bit DAC |
| AD8303AN | +3 V, Dual, Serial Input Complete 12-Bit DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8206YR-REEL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply 42 V System Difference Amplifier |
| AD8206YRZ | 功能描述:IC AMP DIFF 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| AD8206YRZ-REEL | 功能描述:IC AMP DIFF 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| AD8206YRZ-REEL7 | 功能描述:IC AMP DIFF 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| AD8207 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Zero-Drift, High Voltage, Bidirectional Difference Amplifier |
發布緊急采購，3分鐘左右您將得到回復。