- 您現在的位置：買賣IC網 > PDF目錄11804 > AD8153ACPZ (Analog Devices Inc)IC SW MUX/DEMUX SGL BUFF 32LFCSP PDF資料下載
參數資料
| 型號： | AD8153ACPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/24頁 |
| 文件大小： | 0K |
| 描述： | IC SW MUX/DEMUX SGL BUFF 32LFCSP |
| 標準包裝： | 1 |
| 系列： | XStream™ |
| 應用： | 2:1 多路復用器/1:2 多路分配器 |
| 接口： | I²C |
| 電源電壓： | 3 V ~ 3.6 V |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-EP（5x5） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 801 (CN2011-ZH PDF) |
| 配用： | AD8153-EVALZ-ND - BOARD EVALUATION FOR AD8153 |
AD8153
Rev. 0 | Page 16 of 24
I2C DATA WRITE
To write data to the AD8153 register set, a microcontroller, or
any other I2C master, needs to send the appropriate control
signals to the AD8153 slave device. The steps that need to be
followed are listed below, where the signals are controlled by the
I2C master unless otherwise specified. A diagram of the procedure
is shown in Figure 32.
1. Send a start condition (while holding the SCL line high, pull
the SDA line low).
2. Send the AD8153 part address (seven bits) whose upper
four bits are the static value b1001 and whose lower three
bits are controlled by the input pins I2C_A[2:0]. This
transfer should be MSB first.
3. Send the write indicator bit (0).
4. Wait for the AD8153 to acknowledge the request.
5. Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
6. Wait for the AD8153 to acknowledge the request.
7. Send the data (eight bits) to be written to the register whose
address was set in Step 5. This transfer should be MSB first.
8. Wait for the AD8153 to acknowledge the request.
9. Send a stop condition (while holding the SCL line high, pull
the SDA line high) and release control of the bus.
10. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 in this
procedure to perform another write.
11. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 of the
read procedure (in the I2C Data Read section) to perform a
read from another address.
12. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with step 8 of the
read procedure (in the I2C Data Read section) to perform a
read from the same address set in Step 5.
The AD8153 write process is shown in Figure 32. The SCL
signal is shown along with a general write operation and a
specific example. In the example, data 0x92 is written to
Address 0x6D of an AD8153 part with a part address of 0x4B.
The part address is seven bits wide and is composed of the
AD8153 static upper four bits (b1001) and the pin
programmable lower three bits (I2C_ADDR[2:0]). In this
example, the I2C_ADDR bits are set to b011. In Figure 32, the
corresponding step number is visible in the circle under the
waveform. The SCL line is driven by the I2C master and never
by the AD8153 slave. As for the SDA line, the data in the shaded
polygons is driven by the AD8153, whereas the data in the non-
shaded polygons is driven by the I2C master. The end phase case
shown is that of 9a.
It is important to note that the SDA line only changes when the
SCL line is low, except for the case of sending a start, stop, or
repeated start condition, Step 1 and Step 9 in this case.
SCL
SDA
(GENERAL CASE)
SDA
(EXAMPLE)
START
FIXED PART ADDR
ADDR
[2:0]
RW ACK
REGISTER ADDR
ACK
DATA
ACK STOP
12
3
4
25
6
7
06
39
3-
00
4
8
9a
Figure 32. I2C Write Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MS27467E15B97SA | CONN PLUG 12POS STRAIGHT W/SCKT |
| V28C36H100BG2 | CONVERTER MOD DC/DC 36V 100W |
| V28C36H100BG | CONVERTER MOD DC/DC 36V 100W |
| AD9393BBCZ-80 | IC INTERFACE 80MHZ HDMI 76CSPBGA |
| V28C36H100BF2 | CONVERTER MOD DC/DC 36V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8153ACPZ-RL7 | 功能描述:IC SW MUX/DEMUX SGL BUFF 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:XStream™ 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD8153-EVALZ | 功能描述:BOARD EVALUATION FOR AD8153 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:XStream™ 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| AD8153XCPZ | 制造商:Analog Devices 功能描述:SINGLE-LANE 3.2GBPS 2:1 MUX / 1:2 DEMUX SWITCH 32-PIN LFCSP - Bulk |
| AD8155 | 制造商:AD 制造商全稱:Analog Devices 功能描述:6.5 Gbps Dual Buffer Mux/Demux |
| AD8155ACPZ | 功能描述:IC MUX/DEMUX DUAL BUFFER 64LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。