- 您現在的位置：買賣IC網 > PDF目錄375242 > AD8153 (Analog Devices, Inc.) 3.2 Gbps Single Buffered Mux/Demux Switch PDF資料下載
參數資料
| 型號： | AD8153 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 3.2 Gbps Single Buffered Mux/Demux Switch |
| 中文描述： | 3.2 Gbps的單緩沖/解復用器開關 |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 587K |
| 代理商： | AD8153 |
AD8153
I
2
C DATA WRITE
To write data to the AD8153 register set, a microcontroller, or
any other I
2
C master, needs to send the appropriate control
signals to the AD8153 slave device. The steps that need to be
followed are listed below, where the signals are controlled by the
I
2
C master unless otherwise specified. A diagram of the procedure
is shown in Figure 32.
1.
Send a start condition (while holding the SCL line high, pull
the SDA line low).
2.
Send the AD8153 part address (seven bits) whose upper
four bits are the static value b1001 and whose lower three
bits are controlled by the input pins I2C_A[2:0]. This
transfer should be MSB first.
3.
Send the write indicator bit (0).
4.
Wait for the AD8153 to acknowledge the request.
5.
Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
6.
Wait for the AD8153 to acknowledge the request.
7.
Send the data (eight bits) to be written to the register whose
address was set in Step 5. This transfer should be MSB first.
8.
Wait for the AD8153 to acknowledge the request.
9.
Send a stop condition (while holding the SCL line high, pull
the SDA line high) and release control of the bus.
Rev. 0 | Page 16 of 24
10.
Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 in this
procedure to perform another write.
11.
Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 of the
read procedure (in the I
2
C Data Read section) to perform a
read from another address.
12.
Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with step 8 of the
read procedure (in the I
2
C Data Read section) to perform a
read from the same address set in Step 5.
The AD8153 write process is shown in Figure 32. The SCL
signal is shown along with a general write operation and a
specific example. In the example, data 0x92 is written to
Address 0x6D of an AD8153 part with a part address of 0x4B.
The part address is seven bits wide and is composed of the
AD8153 static upper four bits (b1001) and the pin
programmable lower three bits (I2C_ADDR[2:0]). In this
example, the I2C_ADDR bits are set to b011. In Figure 32, the
corresponding step number is visible in the circle under the
waveform. The SCL line is driven by the I
2
C master and never
by the AD8153 slave. As for the SDA line, the data in the shaded
polygons is driven by the AD8153, whereas the data in the non-
shaded polygons is driven by the I
2
C master. The end phase case
shown is that of 9a.
It is important to note that the SDA line only changes when the
SCL line is low, except for the case of sending a start, stop, or
repeated start condition, Step 1 and Step 9 in this case.
SCL
SDA
(GENERAL CASE)
SDA
(EXAMPLE)
START
FIXED PART ADDR
ADDR
[2:0]
RW ACK
REGISTER ADDR
ACK
DATA
ACK
STOP
1
2
3
4
2
5
6
7
0
8
9a
Figure 32. I
2
C Write Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD8153_07 | 3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153ACPZ | 3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153ACPZ-RL7 | 3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153-EVALZ | 3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8159 | 3.2 Gbps Quad Buffer Mux/Demux |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8153_07 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153ACPZ | 功能描述:IC SW MUX/DEMUX SGL BUFF 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:XStream™ 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD8153ACPZ-RL7 | 功能描述:IC SW MUX/DEMUX SGL BUFF 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:XStream™ 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD8153-EVALZ | 功能描述:BOARD EVALUATION FOR AD8153 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:XStream™ 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| AD8153XCPZ | 制造商:Analog Devices 功能描述:SINGLE-LANE 3.2GBPS 2:1 MUX / 1:2 DEMUX SWITCH 32-PIN LFCSP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。