- 您現在的位置：買賣IC網 > PDF目錄378276 > AD8152 (Analog Devices, Inc.) 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch PDF資料下載
參數資料
| 型號： | AD8152 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| 中文描述： | 34 × 34，3.2 Gbps的異步數字交叉點開關 |
| 文件頁數： | 23/32頁 |
| 文件大?。?/td> | 1351K |
| 代理商： | AD8152 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
REV. A
AD8152
–23–
ECL
DRIVER
TO 50
SCOPE
INPUTS
VCC
VTTO
VTTI
= –2V
VEE
= –2.5V
AD8152
P
P
N
N
IN
OUT
Figure 15. Evaluation Board ECL Driver Test Setup
Connections for Testing
The AD8152 evaluation board can be used under a variety of posi-
tive or negative supply configurations. Negative supply configurations,
as shown in Figure 15, allow the easiest hookup to test equip-
ment because inputs and outputs can be direct coupled. In a real
world application however, the negative supply configuration would
be difficult because control logic levels must be shifted negative.
Figure 16 is an example of a loop-through test setup using a posi-
tive supply. In this case, the test signal goes through the AD8152
twice. It is possible to loop through multiple times if desired, but
jitter will increase with number of loop-throughs. The first
input from the generator and the last output to a scope must be
ac-coupled. However, an AD8152 output driving its own input can
be direct-coupled. Direct coupling to the first AD8152 input is not
effective since generators usually want to see 50
W
to ground.
This would require VTTI to be attached to ground, causing
excessive power to be dissipated in the internal 50
W
input
termination resistors. Secondly, when the AD8152 output tries
to drive its own input with VTTI = 0 V and VTTO = 2.5 V, the
input will pull the output stage levels down enough to shut off
any signal toggling.
All ac coupling shown is actually done with a set of bias tees. If
desired, the bias tee can be used to monitor average dc voltage
levels at an input or output (depending on direction installed),
and it can also serve to change input dc levels. Make sure the
bias tees used in the setup have enough low frequency bandwidth
to pass long patterns and keep edge rates intact. The longer the
pattern, the more low frequency bandwidth is needed.
If ac coupling is desired on a user board, 0402 or 0603 sized
capacitors can be installed on microstrip lines. The biggest 0402
size, XR7 type usable is 0.01
m
F, which will work fine for short
patterns (PRBS 2
7
–1) and data rates down to 1.0 Gbps. For
long patterns a 0603 sized, XR7 type, 0.1
m
F should be used. To
decrease capacitive loading from the mounting area, clear out
planes underneath the coupling capacitor.
In Figure 16, 6 dB attenuators are placed before the AD8152
input ac-coupling or bias tees. This is because many generators
won’t go below 500 mV single-ended. The output pair of 6 dB
attenuators is present to protect the scope inputs and allow for
higher scale voltages per division. The eye diagram is usually
viewed differentially by using a simple P – N math function.
Cabling used in this setup must be matched. Mismatched cables
cause either a P or N signal to be falsely delayed. This delay can
show up as a change in the crossing point, from 50 percent in the
eye diagram. To accurately check cable matches, a TDR setup
is recommended.
PATTERN
GENERATOR
VCC
VTTO
2.5V
AD8152
P
P
N
N
IN01
OUT01
VTTI
P
N
P
N
IN02
OUT02
VEE
50
50
DATA OUT
DATA
OUT
TRIGGER OUT
TRIGGER IN
HIGH SPEED
SAMPLING
OSCILLOSCOPE
–6dB
–6dB
–6dB
–6dB
VCC = VTTI = VTTO = 2.5V, VEE = 0V,
SET = 16mA
RTI (REFERRED TO INPUT) A MPLITUDE = 400mV SINGLE–ENDED,
V
IN
HI = 2.7V (IN01), PRBS 2
–1, V
OH
= 2.5V,
V
= 2.1V,
AC-COUPLED IS FROM BIAS TEES,
PROGRAMMING: IN01 TO OUT02, IN02 TO OUT01.
Figure 16. Positive Supply Loop-Through Test Setup
相關PDF資料 |
PDF描述 |
|---|---|
| AD8152-EVAL | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD8152JBP | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD82550A | Stereo Digital Audio Amplifier with Headphone Driver |
| AD82550A-CG | Stereo Digital Audio Amplifier with Headphone Driver |
| AD82551A | Stereo Digital Audio Amplifier with Headphone Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8152-EVAL | 制造商:Analog Devices 功能描述:EVAL KIT FOR ASYNCH DGTL CROSSPOINT SWIT - Bulk |
| AD8152JBP | 功能描述:IC CROSSPOINT SWIT 34X34 256BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| AD8152JBPZ | 功能描述:IC CROSSPOINT SWIT 34X34 256BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| AD8153 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153_07 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.2 Gbps Single Buffered Mux/Demux Switch |
發布緊急采購，3分鐘左右您將得到回復。