參數資料
型號： AD8130ARMZ-REEL7
廠商： Analog Devices Inc
文件頁數： 32/41頁
文件大小： 0K
描述： IC AMP DIFF LN LDIST 40MA 8MSOP
設計資源： High CMRR Circuit for Converting Wideband Complementary DAC Outputs to Single-Ended Without Precision Resistors (CN0142)
標準包裝： 1,000
放大器類型： 差分
電路數： 1
轉換速率： 1100 V/µs
-3db帶寬： 290MHz
電流 - 輸入偏壓： 500nA
電壓 - 輸入偏移： 400µV
電流 - 電源： 13mA
電流 - 輸出 / 通道： 40mA
電壓 - 電源，單路/雙路(±)： 4.5 V ~ 25.2 V，±2.25 V ~ 12.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 帶卷 (TR)
AD8129/AD8130
Rev. C | Page 37 of 40
Another problem can occur with the AD8129 operating
at a supply voltage of greater than or equal to ±12 V. The
architecture causes the supply current to increase as the input
differential voltage increases. If the AD8129 differential inputs
are overdriven too far, excessive current can flow into the device
and potentially cause permanent damage.
A practical means to prevent this from occurring is to clamp the
inputs differentially with a pair of antiparallel Schottky diodes
(see Figure 146). These diodes have a lower forward voltage of
approximately 0.4 V. If the differential voltage across the inputs
is restricted to these conditions, no excess current is drawn by
the AD8129 under these operating conditions.
If the supply voltage is restricted to less than ±11 V, the internal
clamping circuit limits the differential voltage and excessive
supply current is not drawn. The external clamp circuit is not
needed.
VIN
AGILENT
HSMS 2822
1
2
3
VOUT
–V
+V
–VS
PD
+VS
+
VIN
AD8129
6
2
5
4
8
1
3
7
0.1
μF
10
μF
0.1
μF10μF
02464-147
Figure 146. Schottky Diodes Across the Inputs
Limits the Input Differential Voltage
In both circuits, the input series resistors function to limit the
current through the diodes when they are forward biased. As a
practical matter, these resistors must be matched so that the
CMRR is preserved at high frequencies. These resistors have
minimal effect on the CMRR at low frequency.
POWER DISSIPATION
The AD8129/AD8130 can operate with supply voltages from
+5 V to ±12 V. The major reason for such a wide supply range is
to provide a wide input common-mode range for systems that
can require this. This would be encountered when significant
common-mode noise couples into the input path. For applications
that do not require a wide dynamic range for the input or output, it
is recommended to operate with lower supply voltages.
The AD8129/AD8130 is also available in a very small 8-lead
MSOP package. This package has higher thermal impedance
than larger packages and operates at a higher temperature with
the same amount of power dissipation. Certain operating
conditions that are within the specifications range of the parts can
cause excess power dissipation. Caution should be exercised.
The power dissipation is a function of several operating
conditions, including the supply voltage, the input differential
voltage, the output load, and the signal frequency.
A basic starting point is to calculate the quiescent power
dissipation with no signal and no differential input voltage.
This is just the product of the total supply voltage and the
quiescent operating current. The maximum operating supply
voltage is 26.4 V, and the quiescent current is 13 mA. This
causes a quiescent power dissipation of 343 mW. For the
MSOP package, the θJA specification is 142°C/W. Therefore,
the quiescent power causes about a 49°C rise above ambient
in the MSOP package.
The current consumption is also a function of the differential
input voltage (see Figure 113 and Figure 114). This current
should be added onto the quiescent current and then multiplied
by the total supply voltage to calculate the power.
The AD8129/AD8130 can directly drive loads of as low as
100 Ω, such as a terminated 50 Ω cable. The worst-case power
dissipation in the output stage occurs when the output is at
midsupply. As an example, for a 12 V supply with the output
driving a 250 Ω load to ground, the maximum power dissipation
in the output occurs when the output voltage is 6 V. The load
current is 6 V/250 Ω = 24 mA. This same current flows through
the output across a 6 V drop from VS. It dissipates 144 mW. For
the 8-lead MSOP package, this causes a temperature rise of
20°C above ambient. Although this is a worst-case number, it is
apparent that this can be a considerable additional amount of
power dissipation.
Several changes can be made to alleviate this. One is to use the
standard 8-lead SOIC package. This lowers the thermal impedance
to 121°C/W, which is a 15% improvement. Another is to use a
lower supply voltage unless absolutely necessary.
Finally, do not use the AD8129/AD8130 when it is operating on
high supply voltages to directly drive a heavy load. It is best to
use a second op amp after the output stage. Some of the gain
can be shifted to this stage so that the signal swing at the output
of the AD8129/AD8130 is not too large.
相關PDF資料
PDF描述
0001.2709.11 FUSE 3.15A 250V 5X20 T-LAG SMD
0001.2708.11 FUSE 2.5A 250V 5X20 T-LAG SMD
0001.2704.11 FUSE 1A 250V 5X20 T-LAG SMD
AD8129ARZ-REEL7 IC AMP DIFF LN LDIST 40MA 8SOIC
EL8170ISZ-T7 IC AMP INST SGL R-R MCRPWR 8SOIC
相關代理商/技術參數
參數描述
AD8130AR-REEL 制造商:Analog Devices 功能描述:SP Amp DIFF Receiver Amp Single 制造商:Rochester Electronics LLC 功能描述:SOIC LO-COST HI-SPD DIFFERENT'L RECEIVER - Tape and Reel
AD8130AR-REEL1 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost 270 MHz Differential Receiver Amplifiers
AD8130AR-REEL7 功能描述:IC AMP DIFF LN LDIST 40MA 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
AD8130AR-REEL72 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost 270 MHz Differential Receiver Amplifiers
AD8130ARZ 功能描述:IC AMP DIFF LN LDIST 40MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*