- 您現在的位置：買賣IC網 > PDF目錄375242 > AD8112 (Analog Devices, Inc.) Audio/Video, 60 MHz, 16 】 8, Gain of +2 Crosspoint Switch PDF資料下載
參數資料
| 型號： | AD8112 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Audio/Video, 60 MHz, 16 】 8, Gain of +2 Crosspoint Switch |
| 中文描述： | 音頻/視頻，60兆赫，16】8，2交叉點開關增益 |
| 文件頁數： | 21/28頁 |
| 文件大小： | 412K |
| 代理商： | AD8112 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD8112
Video signals usually use 75 Ω transmission lines that need to
be terminated with this value of resistance at each end. When
such a source is delivered to one of the AD8112 inputs, the high
input impedance does not properly terminate these signals.
Therefore, the line should be terminated with a 75 Ω shunt
resistor to ground. Because video signals are limited in their
peak-to-peak amplitude, there is no need to attenuate video
signals before they pass through the AD8112.
Rev. 0 | Page 21 of 28
The basic concept in constructing larger crosspoint arrays is
to connect inputs in parallel in a horizontal direction and to
wire-OR the outputs together in the vertical direction. The
meaning of horizontal and vertical can best be understood by
looking at Figure 46, which illustrates this concept for a 32 × 16
crosspoint array that uses four AD8112s.
1k
AD8112
AD8112
IN00 TO IN15
IN16 TO IN31
AD8112
AD8112
1k
1k
1k
16
16
16
16
8
8
8
8
8
8
0
The AD8112 outputs are very low impedance and do not prop-
erly terminate the source end of a 75 Ω transmission line. In
these cases, a series 75 Ω resistor should be inserted at an output
that drives a video signal. Then the transmission line should be
terminated with 75 Ω at its far end. This overall termination
scheme divides the amplitude of the AD8112 output by 2. An
overall unity gain channel is produced as a result of the
AD8112’s channel gain of +2.
CREATING LARGER CROSSPOINT ARRAYS
The AD8112 is a high density building block for creating
crosspoint arrays of dimensions larger than 16 × 8. Various
features, such as output disable and chip enable, are useful
for creating larger arrays.
Figure 46. 32 x 16 Audio Crosspoint Array Using Four AD8112s
The inputs are individually assigned to each of the 32 inputs of
the two devices and a divider is used to normalize the channel
gain. The outputs are wire-OR’ed together in pairs. The output
from only one wire-OR’ed pair should be enabled at any given
time. The device programming software must be properly
written to for this to happen.
The first consideration in constructing a larger crosspoint is
to determine the minimum number of devices required. The
16 × 8 architecture of the AD8112 contains 128 points, which
is a factor of 32 greater than a 4 × 1 crosspoint (or multiplexer).
The PC board area, power consumption, and design effort
savings are readily apparent when compared with using these
smaller devices.
Using additional crosspoint devices in the design can lower the
number of outputs that must be wire-OR’ed together. Figure 47
shows a block diagram of a system using ten AD8112s to create
a nonblocking, gain of +2, 128 × 8 crosspoint that restricts the
wire-OR’ing at the output to only four outputs.
For a nonblocking crosspoint, the number of points required is
the product of the number of inputs multiplied by the number
of outputs. Nonblocking requires that the programming of a
given input to one or more outputs does not restrict the avail-
ability of that input to be a source for any other outputs.
Additionally, by using the lower eight outputs from each of the
two Rank 2 AD8112s, a blocking 128 × 16 crosspoint array can
be realized. There are, however, some drawbacks to this technique.
The offset voltages of the various cascaded devices accumulate,
and the bandwidth limitations of the devices compound. In
addition, the extra devices consume more current and take up
more board space. Consider the overall system design speci-
fications when using the various trade-offs.
Some nonblocking crosspoint architectures require more than
this minimum as previously calculated. Also, there are blocking
architectures that can be constructed with fewer devices than
this minimum. These systems have connectivity available on a
statistical basis that is determined when designing the overall
system.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8112-EVALZ1 | Audio/Video, 60 MHz, 16 】 8, Gain of +2 Crosspoint Switch |
| AD8112JSTZ1 | Audio/Video, 60 MHz, 16 】 8, Gain of +2 Crosspoint Switch |
| AD8116-EB | 200 MHz, 16 x 16 Buffered Video Crosspoint Switch |
| AD8116JST | 200 MHz, 16 x 16 Buffered Video Crosspoint Switch |
| AD8128 | CAT-5 Receiver with Adjustable Line Equalization |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8112-EVALZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Audio/Video, 60 MHz, 16 】 8, Gain of +2 Crosspoint Switch |
| AD8112JSTZ | 功能描述:IC CROSSPOINT SWIT 16X8 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| AD8112JSTZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Audio/Video, 60 MHz, 16 】 8, Gain of +2 Crosspoint Switch |
| AD8113 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Audio/Video 60 MHz 16 X 16, G = + 2 Crosspoint Switch |
| AD8113-EVAL | 制造商:Analog Devices 功能描述:AD8113 EVALUATION BOARD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。