- 您現在的位置：買賣IC網 > PDF目錄373932 > AD8054 (Analog Devices, Inc.) Low Cost, High Speed Rail-to-Rail Amplifiers(低成本,高速滿幅度四放大器) PDF資料下載
參數資料
| 型號： | AD8054 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Cost, High Speed Rail-to-Rail Amplifiers(低成本,高速滿幅度四放大器) |
| 中文描述： | 低成本，高速軌到軌放大器（低成本，高速滿幅度四放大器） |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 256K |
| 代理商： | AD8054 |
–13–
AD8051/AD8052/AD8054
REV. 0
problems caused by junction isolation. T hese features allow the
construction of high frequency, low distortion amplifiers with low
supply currents. T his design uses a differential output input stage
to maximize bandwidth and headroom (see Figure 1). T he smaller
signal swings required on the first stage outputs (nodes S1P, S1N)
reduce the effect of nonlinear currents due to junction capacitances
and improve the distortion performance. With this design har-
monic distortion of –80 dBc @ 1 MHz into 100
with V
OUT
= 2
V p-p (Gain = +1) on a single 5 volt supply is achieved.
T he inputs of the device can handle voltages from –0.2 V below
the negative rail to within 1 V of the positive rail. Exceeding
these values will not cause phase reversal; however, the input
ESD devices will begin to conduct if the input voltages exceed
the rails by greater than 0.5 V. During this overdrive condition,
the output stays at the rail.
T he rail-to-rail output range of the AD8051/AD8052/AD8054
is provided by a complementary common-emitter output stage.
High output drive capability is provided by injecting all out-
put stage predriver currents directly into the bases of the output
devices Q8 and Q36. Biasing of Q8 and Q36 is accomplished by
I8 and I5, along with a common-mode feedback loop (not
shown). T his circuit topology allows the AD8051/AD8052 to drive
45 mA of output current and the AD8054 to drive 30mA of out-
put current with the outputs within 0.5 V of the supply rails.
I10
R39
Q5
Q40
V
EE
I2
I3
Q25
Q50
Q51
Q39
Q22
Q7
Q21
Q27
Q31
R23 R27
Q23
I9
Q36
I5
V
EE
C3
V
OUT
C9
Q8
I8
V
CC
I11
Q47
Q24
I7
Q11
R3
R21
R5
Q3
Q2
SIP
SIN
Q1
Q13
C7
V
EE
V
IN
N
V
IN
P
Q4
R15 R2
V
CC
R26
Figure 41. AD8051/AD8052 Simplified Schematic
APPLICAT IONS
Layout Considerations
T he specified high speed performance of the AD8051/AD8052/
AD8054 requires careful attention to board layout and compo-
nent selection. Proper RF design techniques and low-parasitic
component selection are necessary.
T he PCB should have a ground plane covering all unused por-
tions of the component side of the board to provide a low im-
pedance path. T he ground plane should be removed from the
area near the input pins to reduce the parasitic capacitance.
Chip capacitors should be used for the supply bypassing. One
end should be connected to the ground plane and the other
within 3 mm of each power pin. An additional large (4.7
μ
F to
10
μ
F) tantalum electrolytic capacitor should be connected in
parallel, but not necessarily so close, to supply current for fast,
large signal changes at the output.
T he feedback resistor should be located close to the inverting
input pin in order to keep the parasitic capacitance at this node
to a minimum. Parasitic capacitance of less than 1 pF at the
inverting input can significantly affect high speed performance.
Stripline design techniques should be used for long signal traces
(greater than about 25 mm). T hese should be designed with a
characteristic impedance of 50
or 75
and be properly termi-
nated at each end.
Active Filters
Active filters at higher frequencies require wider bandwidth op
amps to work effectively. Excessive phase shift produced by
lower frequency op amps can significantly impact active filter
performance.
Figure 42 shows an example of a 2 MHz biquad bandwidth
filter that uses three op amps of an AD8054. Such circuits are
sometimes used in medical ultrasound systems to lower the
noise bandwidth of the analog signal before A/D conversion.
Please note that the unused amplifiers’ inputs should be tied to
ground.
12
13
14
2
1
R1
3k
V
V
IN
R2
2k
V
C1
50pF
R3
2k
V
6
5
7
R6
1k
V
R5
2k
V
9
10
8
AD8054
AD8054
AD8054
C2
50pF
V
OUT
R4
2k
V
3
Figure 42. 2 MHz Biquad Bandpass Filter Using AD8054
T he frequency response of the circuit is shown in Figure 43.
FREQUENCY – Hz
10k
100M
100k
1M
10M
0
2
10
2
20
2
30
2
40
G
Figure 43. Frequency Response of 2 MHz Bandpass
Biquad Filter
A/D and D/A Applications
Figure 44 is a schematic showing the AD8051 used as a driver
for an AD9201, a 10-bit 20 MSPS dual A/D converter. T his
converter is designed to convert I and Q signals in communica-
tion systems. In this application, only the I channel is being
driven. T he I channel is enabled by applying a logic HIGH to
SELECT , Pin 27.
T he AD8051 is running from a dual supply and is configured
for a gain of +2. T he input signal is terminated in 50
and
相關PDF資料 |
PDF描述 |
|---|---|
| AD8055AR-REEL | Low Cost, 300 MHz Voltage Feedback Amplifiers |
| AD8055AR-REEL7 | Low Cost, 300 MHz Voltage Feedback Amplifiers |
| AD8055AN | 16-Bit 250 kSPS ADC Par. Out, 4 true bipolar chanels 48-TQFP -40 to 85 |
| AD8055AR | Low Cost, 300 MHz Voltage Feedback Amplifiers |
| AD8055ART-REEL | 16-Bit 250 kSPS ADC Par. Out, 4 true bipolar chanels 48-TQFP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8054AR | 功能描述:IC OPAMP VF R-R QUAD LP 14SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| AD8054AR-EBZ | 功能描述:BOARD EVAL FOR AD8054AR RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8054AR-REEL | 功能描述:IC OPAMP VF R-R QUAD LP 14SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| AD8054AR-REEL7 | 功能描述:IC OPAMP VF R-R QUAD LP 14SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD8054ARU | 功能描述:IC OPAMP VF R-R QUAD LP 14TSSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。