- 您現在的位置：買賣IC網 > PDF目錄6068 > AD8045ARDZ (Analog Devices Inc)IC OPAMP VF ULDIST LN 70MA 8SOIC PDF資料下載
參數資料
| 型號： | AD8045ARDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP VF ULDIST LN 70MA 8SOIC |
| 產品培訓模塊： | Practical Guide High Speed PCB Layout |
| 標準包裝： | 98 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 1 |
| 轉換速率： | 1350 V/µs |
| -3db帶寬： | 1GHz |
| 電流 - 輸入偏壓： | 2µA |
| 電壓 - 輸入偏移： | 200µV |
| 電流 - 電源： | 16mA |
| 電流 - 輸出 / 通道： | 70mA |
| 電壓 - 電源，單路/雙路(±)： | 3.3 V ~ 12 V，±1.65 V ~ 6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 8-SOIC-EP |
| 包裝： | 管件 |
| 產品目錄頁面： | 769 (CN2011-ZH PDF) |
AD8045
Rev. A | Page 23 of 24
EXPOSED PADDLE
The AD8045 features an exposed paddle, which lowers the
thermal resistance by 25% compared to a standard SOIC plastic
package. The exposed paddle of the AD8045 is internally con-
nected to the negative power supply pin. Therefore, when laying
out the board, the exposed paddle must either be connected to
the negative power supply or left floating (electrically isolated).
Soldering the exposed paddle to the negative power supply metal
ensures maximum thermal transfer. Figure 74 and Figure 75 show
the proper layout for connecting the SOIC and LFCSP exposed
paddle to the negative supply.
04814-0-071
Figure 74. SOIC Exposed Paddle Layout
The use of thermal vias or “heat pipes” can also be incorporated
into the design of the mounting pad for the exposed paddle.
These additional vias help to lower the overall theta junction to
ambient (θJA). Using a heavier weight copper on the surface to
which the amplifier’s exposed paddle is soldered can greatly
reduce the overall thermal resistance “seen” by the AD8045.
04814-0-073
Figure 75. LFCSP Exposed Paddle Layout
For existing designs that want to incorporate the AD8045,
electrically isolating the exposed paddle is another option. If the
exposed paddle is electrically isolated, the thermal dissipation is
primarily through the leads, and the thermal resistance of the
package now approaches 125°C/W, the standard SOIC θJA.
However, a thermally conductive and electrically isolated pad
material may be used. A thermally conductive spacer, such as
the Bergquist Company’s Sil-Pad, is an excellent solution to this
problem. Figure 76 shows a typical implementation using
thermal pad material.
04814-0-072
THERMAL CONDUCTIVE INSULATOR
Figure 76. SOIC with Thermal Conductive Pad Material
The thermal pad provides high thermal conductivity but
isolates the exposed paddle from ground or other potential. It is
recommended, when possible, to solder the paddle to the nega-
tive power supply plane or trace for maximum thermal transfer.
Note that soldering the paddle to ground shorts the negative
power supply to ground and can cause irreparable damage to
the AD8045.
DRIVING CAPACITIVE LOADS
In general, high speed amplifiers have a difficult time driving
capacitive loads. This is particularly true in low closed-loop
gains, where the phase margin is the lowest. The difficulty arises
because the load capacitance, CL, forms a pole with the output
resistance, RO, of the amplifier. The pole can be described by the
equation
L
O
P
C
R
f
2π
1
=
If this pole occurs too close to the unity gain crossover point,
the phase margin degrades. This is due to the additional phase
loss associated with the pole.
The AD8045 output can drive 18 pF of load capacitance directly,
in a gain of +2 with 30% overshoot, as shown in Figure 37.
Larger capacitance values can be driven but must use a snub-
bing resistor (RSNUB) at the output of the amplifier, as shown in
creates a zero that cancels the pole introduced by the load
capacitance. Typical values for RSNUB can range from 25 to
50 . The value is typically arrived at empirically and based on
the circuit requirements.
相關PDF資料 |
PDF描述 |
|---|---|
| 0388005.MXEP | FUSE 250V PT FA 3AG METI B 5A |
| AD8202YRZ | IC AMP DIFF 50KHZ 8SOIC |
| RMCF2512FT150R | RES TF 150 OHM 1% 1W 2512 |
| AD8662ARZ | IC OPAMP GP R-R CMOS 4MHZ 8SOIC |
| RMCF2512FT42K2 | RES TF 42.2K OHM 1% 1W 2512 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8045ARDZ-REEL | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8045ARDZ-REEL7 | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8045AR-REEL7 | 制造商:Analog Devices 功能描述:ULTRA-LOW DISTORTION HIGH SPEED AMPLIFIER - Tape and Reel |
| AD8047 | 制造商:AD 制造商全稱:Analog Devices 功能描述:250 MHz, General Purpose Voltage Feedback Op Amps |
| AD8047_03 | 制造商:AD 制造商全稱:Analog Devices 功能描述:250 MHz, General Purpose Voltage Feedback Op Amps |
發布緊急采購，3分鐘左右您將得到回復。