- 您現在的位置：買賣IC網 > PDF目錄5391 > AD8039ARZ-REEL (Analog Devices Inc)IC OPAMP VF DUAL LP LN 8SOIC PDF資料下載
參數資料
| 型號： | AD8039ARZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/17頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF DUAL LP LN 8SOIC |
| 標準包裝： | 2,500 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 2 |
| 轉換速率： | 425 V/µs |
| -3db帶寬： | 350MHz |
| 電流 - 輸入偏壓： | 400pA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 1mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 12 V，±1.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
AD8038/AD8039
Rev. G | Page 13 of 16
LAYOUT, GROUNDING, AND BYPASSING CONSIDERATIONS
DISABLE
The AD8038 in the 8-lead SOIC package provides a disable
feature. This feature disables the input from the output (see
Figure 42 for input-output isolation) and reduces the quiescent
current from typically 1 mA to 0.2 mA. When the DISABLE
node is pulled below 4.5 V from the positive supply rail, the part
becomes disabled. To enable the part, the DISABLE node needs
to be pulled to greater than (VS – 2.5).
POWER SUPPLY BYPASSING
Power supply pins are actually inputs, and care must be taken
so that a noise-free stable dc voltage is applied. The purpose of
bypass capacitors is to create low impedances from the supply
to ground at all frequencies, thereby shunting or filtering a
majority of the noise.
Decoupling schemes are designed to minimize the bypassing
impedance at all frequencies with a parallel combination of
capacitors. The 0.01 μF or 0.001 μF (X7R or NPO) chip capacitors
are critical and should be placed as close as possible to the
amplifier package. Larger chip capacitors, such as 0.1 μF
capacitors, can be shared among a few closely spaced active
components in the same signal path. A 10 μF tantalum capacitor
is less critical for high frequency bypassing and, in most cases,
only one per board is needed at the supply inputs.
GROUNDING
A ground plane layer is important in densely packed PC boards
to spread the current minimizing parasitic inductances. However,
an understanding of where the current flows in a circuit is critical
to implementing effective high speed circuit design. The length
of the current path is directly proportional to the magnitude of
parasitic inductances and, therefore, the high frequency impedance
of the path. High speed currents in an inductive ground return
create an unwanted voltage noise.
The length of the high frequency bypass capacitor leads is most
critical. A parasitic inductance in the bypass grounding works
against the low impedance created by the bypass capacitor. Because
load currents flow from the supplies as well, the ground for the
load impedance should be at the same physical location as the
bypass capacitor grounds. For the larger value capacitors, which
are intended to be effective at lower frequencies, the current
return path distance is less critical.
INPUT CAPACITANCE
Along with bypassing and ground, high speed amplifiers can be
sensitive to parasitic capacitance between the inputs and ground. A
few picofarads of capacitance reduces the input impedance at
high frequencies, in turn increasing the gain of the amplifiers,
causing peaking of the frequency response, or even oscillations
if severe enough. It is recommended that the external passive
components that are connected to the input pins be placed as
close as possible to the inputs to avoid parasitic capacitance.
The ground and power planes must be kept at a distance of at
least 0.05 mm from the input pins on all layers of the board.
OUTPUT CAPACITANCE
To a lesser extent, parasitic capacitances on the output can cause
peaking of the frequency response. Two methods to minimize
this effect include the following:
Put a small value resistor in series with the output to isolate
the load capacitor from the output stage of the amplifier, see
Increase the phase margin with higher noise gains or add
a pole with a parallel resistor and capacitor from IN to
the output.
INPUT-TO-OUTPUT COUPLING
The input and output signal traces should not be parallel to
minimize capacitive coupling between the inputs and outputs,
avoiding any positive feedback.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8614ART-REEL7 | IC OPAMP GP R-R 5.5MHZ SOT23-5 |
| LT6211IMS#TRPBF | IC AMP CURR FDBK DUAL R-R 10MSOP |
| OP27GSZ-REEL | IC OPAMP GP 8MHZ LN PREC 8SOIC |
| LT1782CS6#TRM | IC OPAMP R-R I/O MICRPWR SOT23-6 |
| MMK25-0091HU | CONN RACK/PANEL 9POS 5A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8039ARZ-REEL7 | 功能描述:IC OPAMP VF DUAL LP LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD-8039E | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:ADSL CPE SIDE SPLITTER |
| AD-8039F | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:ADSL CPE SIDE SPLITTER |
| AD-8039J | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:ADSL CPE SIDE SPLITTER |
| AD8039SRZ-EPR7 | 制造商:Analog Devices 功能描述:LOW POWER, 350 MHZ VOLTAGE FEEDBACK AMPLIFIERS - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC OPAMP VFB 350MHZ 8SOIC 制造商:Analog Devices 功能描述:SOIC Dual Low-Pwr Vltg-Fdbk Op Amp |
發布緊急采購，3分鐘左右您將得到回復。