- 您現在的位置：買賣IC網 > PDF目錄6048 > AD8012ARZ (Analog Devices Inc)IC OPAMP CF DUAL LP 125MA 8SOIC PDF資料下載
參數資料
| 型號： | AD8012ARZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP CF DUAL LP 125MA 8SOIC |
| 標準包裝： | 98 |
| 放大器類型： | 電流反饋 |
| 電路數： | 2 |
| 轉換速率： | 2250 V/µs |
| -3db帶寬： | 350MHz |
| 電流 - 輸入偏壓： | 3µA |
| 電壓 - 輸入偏移： | 1500µV |
| 電流 - 電源： | 1.7mA |
| 電流 - 輸出 / 通道： | 125mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 12 V，±1.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
| 產品目錄頁面： | 769 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
REV. B
–14–
AD8012
Choosing the Appropriate Turns Ratio for the Transformer
Increasing the peak-to-peak output signal of the amplifier in the
previous example and adding a variation in the turns ratio of the
transformer can yield further enhancements to the circuit. The
output signal swing of the AD8012 can be increased to about
±3.9 V before clipping occurs. This increases the peak-to-peak
output of the differential amplifier to 15.6 V. Because the signal
applied to the primary winding is now bigger, the transformer
turns ratio of 1:1 can be replaced with a (step-down) turns ratio
of about 1.3:1 (from amplifier to line). This steps the 7.8 V
peak-to-peak primary voltage down to 6 V. This is the same
secondary voltage of the earlier examples, so the resulting power
delivered to the line is the same.
The received signal, which is small relative to the transmitted
signal, will, however, be stepped up by a factor of 1.3. Amplifying
the received signal in this manner enhances its signal-to-noise
ratio and is useful when the received signal is small compared to
the to-be-transmitted signal.
The impedance reflected from the 135
line now becomes
228
(1.32
135
). With a correctly terminated line, the
amplifier must now drive a total load of 456
(114 + 114
+ 228
), considerably more than the original 270 load. This
reduces the drive current from the op amps by about 40%.
More significant, however, is the reduction in dynamic power
consumption—that is, the power the amplifier must consume in
order to deliver the load power. Increasing the output signal so
that it is as close as possible to the power rails minimizes the
power consumed in the amplifier.
There is, however, a price to pay in terms of increased signal
distortion. Increasing the output signal of each op amp from the
original
± 3 V to ± 3.9 V reduces the spurious-free dynamic
range (SFDR) from –65 dB to –50 dB (measured at 500 kHz),
even though the overall load impedance has increased from
270
to 456 .
LAYOUT CONSIDERATIONS
The specified high speed performance of the AD8012 requires
careful attention to board layout and component selection.
Table I shows recommended component values for the AD8012
and Figures 8–13 show recommended layouts for the 8-lead
SOIC and MSOP packages for a positive gain. Proper RF
design techniques and low parasitic component selections
are mandatory.
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance ground path. The ground plane should be removed
from the area near the input pins to reduce stray capacitance.
Chip capacitors should be used for supply bypassing (see Figure 7).
One end should be connected to the ground plane and the other
within 1/8 inch of each power pin. An additional (4.7
F to 10 F)
tantalum electrolytic capacitor should be connected in parallel.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to
a minimum. Capacitance greater than 1.5 pF at the inverting
input will significantly affect high speed performance when
operating at low noninverting gains.
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). They should be designed with the
proper system characteristic impedance and be properly termi-
nated at each end.
0.1 F
INVERTING CONFIGURATION
VOUT
RF
10 F
NONINVERTING CONFIGURATION
VOUT
RG
RF
RT
0.1 F
10 F
RT
VIN
RG
VIN
*RO CHOSEN FOR CHARACTERISTIC IMPEDANCE.
+VS
+
–VS
RO*
*RO CHOSEN FOR CHARACTERISTIC IMPEDANCE.
Figure 7. Inverting and Noninverting Configurations
Table I. Typical Bandwidth vs. Gain Setting Resistors
Small Signal –3 dB BW (MHz),
Gain
RF
RG
RT
VS =
5 V, RL = 1 k
–1
750
750
53.6
110
+1
750
49.9
350
+2
750
750
49.9
150
+10
750
82.5
49.9
40
RT chosen for 50
characteristic input impedance.
相關PDF資料 |
PDF描述 |
|---|---|
| 1SMC54AT3G | TVS 1500W 54V UNIDIRECT SMC |
| 929834-02-14 | CONN HEADER .100 SNGL STR 14POS |
| 1SMC40AT3G | TVS 1500W 40V UNIDIRECT SMC |
| LTC1049CS8#PBF | IC OPAMP CHOP-STBL W/CAPS 8SOIC |
| 159150-6002 | CONN HEADER 2MM 50POS VERT GOLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8012ARZ-REEL | 功能描述:IC OPAMP CF DUAL LP 125MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| AD8012ARZ-REEL7 | 功能描述:IC OPAMP CF DUAL LP 125MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| AD8013 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Supply, Low Power, Triple Video Amplifier |
| AD80135BBCZ | 制造商:Analog Devices 功能描述: |
| AD80135BBCZRL | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。