參數資料
型號： AD7994BRU-0
廠商： Analog Devices Inc
文件頁數： 22/32頁
文件大小： 0K
描述： IC ADC 12BIT 4CHAN I2C 16TSSOP
標準包裝： 96
位數： 12
采樣率（每秒）： 188k
數據接口： I²C，串行
轉換器數目： 1
功率耗散（最大）： 2.2mW
電壓電源： 單電源
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 管件
輸入數目和類型： 4 個單端，單極
AD7993/AD7994
Rev. 0 | Page 29 of 32
MODE 2—COMMAND MODE
This mode allows a conversion to be automatically initiated any
time a write operation occurs. In order to use this mode,
Command Bits C4 to C1 in the address pointer byte, shown in
Table 7, must be programmed.
To select a single analog input for conversion in this mode,
the user must set bits C4 to C1of the address pointer byte to
indicate which channel to convert (see Table 27). When all four
command bits are 0, this mode is not in use.
A sequence can also be set up for this mode. If more than one
command bit is set in the address pointer byte, the ADC starts
converting on the lowest channel in the sequence and then the
next lowest until all the channels in the sequence have been
converted. The ADC stops converting the sequence when it
receives a STOP bit.
Figure 29 illustrates a 2-byte read operation from the conver-
sion result register. This operation is normally preceded by a
write to the address pointer register so that the following read
accesses the desired register, in this case the conversion result
register (Figure 26). If Command Bits C4 to C1 are set when the
contents of the address pointer register are being loaded, the
AD7993/AD7994 begin to power up and convert the selected
channel(s). Power-up begins on the fifth SCL falling edge of the
address point byte (see Point A in Figure 33).
Table 27 shows the channel selection in this mode via
Command Bits C4 to C1 in the address pointer register. The
wake-up and conversion times combined should take
approximately 3 s. Following this, the AD7993/AD7994 must
be addressed again to indicate that a read operation is required.
The read then takes place from the conversion result register.
This read accesses the conversion result from the channel
selected via the command bits. If the Command Bits C2 and C1
were set to 1, 1, then a four byte read would be necessary. The
first read accesses the data from the conversion on VIN1. While
this read takes place, a conversion occurs on VIN2. The second
read accesses this data from VIN2. Figure 34 illustrates how this
mode operates.
When operating the AD7994-1/AD7993-1 in Mode 2 with a
high speed mode, 3.4 MHz SCL, the conversion may not be
complete before the master tries to read the conversion result.
If this is the case, the AD7994-1/AD7993-1 hold the SCL line
low during the ACK clock after the read address until the con-
version is complete. When the conversion is complete, the
AD7994-1/AD7993-1 release the SCL line and the master can
then read the conversion result.
After the conversion is initiated by setting the command bits in
the address pointer byte, if the AD7993/AD7994 receive a stop
or NACK from the master, the devices stop converting.
Table 27. Address Pointer Byte
C4
C3
C2
C1
P3
P2
P1
P0
Mode 2, Convert On
Comments
0
Not selected
0
1
0
VIN1
0
1
0
VIN2
0
1
0
Sequence between VIN1 and VIN2
0
1
0
VIN3
0
1
0
1
0
Sequence between VIN1 and VIN3
0
1
0
Sequence between VIN2 and VIN3
0
1
0
Sequence between VIN1, VIN2, and VIN3
1
0
VIN4
1
0
1
0
Sequence between VIN1 and VIN4
1
0
1
0
Sequence between VIN2 and VIN4
1
0
1
0
Sequence between VIN1, VIN2, and VIN4
1
0
Sequence between VIN3 and VIN4
1
0
1
0
Sequence between VIN1, VIN3, and VIN4
1
0
Sequence between VIN2, VIN3, and VIN4
1
0
Sequence between VIN1, VIN2, VIN3, and VIN4
With the pointer bits set to all 0s, the next
read accesses the results of the conversion
result register.
相關PDF資料
PDF描述
MS27467T13B8PB CONN PLUG 8POS STRAIGHT W/PINS
AD7939BCPZ IC ADC 10BIT 8CH PARALL 32LFCSP
MS27467T11F99P CONN PLUG 7POS STRAIGHT W/PINS
MS27484T10A5P CONN PLUG 5POS STRAIGHT W/PINS
AD7193BCPZ-RL7 IC ADC 24BIT SPI 4.8KHZ 32LFCSP
相關代理商/技術參數
參數描述
AD7994BRU-0REEL 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD7994BRU-1 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 16-Pin TSSOP 制造商:Rochester Electronics LLC 功能描述:
AD7994BRU-1REEL 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 16-Pin TSSOP T/R
AD7994BRUZ0 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD7994BRUZ-0 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*