參數資料
型號： AD7993BRUZ-0
廠商： Analog Devices Inc
文件頁數： 11/32頁
文件大?。?/td> 0K
描述： IC ADC 10BIT 4CH W/I2C 16-TSSOP
標準包裝： 96
位數： 10
采樣率（每秒）： 188k
數據接口： I²C，串行
轉換器數目： 1
功率耗散（最大）： 2.2mW
電壓電源： 單電源
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 管件
輸入數目和類型： 4 個單端，單極
產品目錄頁面： 780 (CN2011-ZH PDF)
AD7993/AD7994
Rev. 0 | Page 19 of 32
CONFIGURATION REGISTER
The configuration register is an 8-bit read/write register that is used to set the operating modes of the AD7993/AD7994. The bit functions
are outlined in Table 9. A single-byte write is necessary when writing to the configuration register.
Table 9. Configuration Register Bit Function Descriptions and Default Settings at Power-Up
D7
D6
D5
D4
D3
D2
D1
D0
CH4
CH3
CH2
CH1
FLTR
ALERT EN
BUSY/ALERT
ALERT/BUSY POLARITY
0
1
0
Table 10. Bit Function Descriptions
Bit
Mnemonic
Comment
D7 to D4
CH4 to CH1
These 4-channel address bits select the analog input channel(s) to be converted. A 1 in any of Bits D7 to D4
selects a channel for conversion. If more than one channel bit is set to 1, the AD7993/AD7994 sequence
through the selected channels, starting with the lowest channel. All unused channels should be set to 0.
Table 11 shows how these 4-channel address bits are decoded. Prior to initiating a conversion, the channel(s)
must be selected in the configuration register.
D3
FLTR
The value written to this bit of the control register determines whether the filtering on SDA and SCL is
enabled or is to be bypassed. If this bit is a 1, then the filtering is enabled; if it is a 0, the filtering is bypassed.
D2
ALERT EN
The hardware ALERT function is enabled if this bit is set to 1 and disabled if this bit is set to 0. This bit is used
in conjunction with the BUSY/ALERT bit to determine if the ALERT/BUSY pin act as an ALERT or a BUSY output
D1
BUSY/ALERT
This bit is used in conjunction with the ALERT EN bit to determine if the ALERT/BUSY output, Pin 13, acts as an
ALERT or BUSY output (see Table 12), and if Pin 13 is configured as an ALERT output pin, if it is to be reset.
D0
BUSY/ALERT
POLARITY
This bit determines the active polarity of the ALERT/BUSY pin regardless of whether it is configured as an
ALERT or BUSY output. It is active low if this bit is set to 0, and active high if it is set to 1.
Table 11. Channel Selection
D7
D6
D5
D4
Analog Input Channel
Comments
0
No channel selected; see address pointer byte, Mode 2.
0
1
Convert on VIN1.
0
1
0
Convert on VIN2.
0
1
Sequence between VIN1 and VIN2.
0
1
0
Convert on VIN3.
0
1
0
1
Sequence between VIN1 and VIN3.
0
1
0
Sequence between VIN2 and VIN3.
0
1
Sequence between VIN1, VIN2, and VIN3.
1
0
Convert on VIN4.
1
0
1
Sequence between VIN1 and VIN4.
1
0
1
0
Sequence between VIN2 and VIN4.
1
0
1
Sequence between VIN1, VIN2, and VIN4.
1
0
Sequence between VIN3 and VIN4.
1
0
1
Sequence between VIN1, VIN3, and VIN4.
1
0
Sequence between VIN2, VIN3, and VIN4.
1
Sequence between VIN1, VIN2, VIN3, and VIN4.
The AD7993/AD7994 convert on the selected channel in
the sequence in ascending order, starting with the
lowest channel in the sequence.
Table 12. Alert/Busy Function
D2
D1
ALERT/BUSY Pin Configuration
0
Pin does not provide any interrupt signal.
0
1
Pin configured as a busy output.
1
0
Pin configured as an alert output.
1
Resets the ALERT output pin, the Alert_Flag bit in the conversion result register, and the entire alert status register
(if any is active). If 1/1 is written to Bits D2/D1 in the configuration register to reset the ALERT pin, the Alert_Flag bit,
and the alert status register, the contents of the configuration register read 1/0 for D2/D1, respectively, if read back.
相關PDF資料
PDF描述
VI-20N-IX-B1 CONVERTER MOD DC/DC 18.5V 75W
LTC2485CDD#PBF IC ADC 24BIT I2C 10-DFN
VE-JWM-MY-F2 CONVERTER MOD DC/DC 10V 50W
LTC1442CS8 IC COMP W/REF LP DUAL 8-SOIC
VI-20M-IX-B1 CONVERTER MOD DC/DC 10V 75W
相關代理商/技術參數
參數描述
AD7993BRUZ-0REEL 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7993BRUZ-1 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7993BRUZ-1REEL 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7993-X 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
AD7994 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*