參數資料
型號: AD7991YRJZ-1500RL7
廠商: Analog Devices Inc
文件頁數: 19/28頁
文件大小: 0K
描述: IC ADC 12BIT 4CH SAR I2C SOT23-8
產品變化通告: AD7991,5,9 Offset Error Change 17/Sept/2010
設計資源: Using AD8599 as an Ultralow Distortion Driver for the AD7991 (CN0043)
標準包裝: 1
位數: 12
采樣率(每秒): 1M
數據接口: I²C,串行
轉換器數目: 1
功率耗散(最大): 4.68mW
電壓電源: 單電源
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: SOT-23-8
供應商設備封裝: SOT-23-8
包裝: 標準包裝
輸入數目和類型: 4 個單端,單極
產品目錄頁面: 780 (CN2011-ZH PDF)
配用: EVAL-AD7991EBZ-ND - BOARD EVAL FOR AD7991
其它名稱: AD7991YRJZ-1500RL7DKR
AD7991/AD7995/AD7999
Rev. B | Page 26 of 28
MODE OF OPERATION
The AD7991/AD7995/AD7999 powers up in shutdown mode.
After the master addresses the AD7991/AD7995/AD7999 with
the correct I2C address, the ADC acknowledges the address. In
response, the AD7991/AD7995/AD7999 power up.
During this wake up time, the AD7991/AD7995/AD7999 exit
shutdown mode and begin to acquire the analog input (acquisition
phase). By default, all channels are selected. Which channels
are converted depends on the status of the channel bits in the
configuration register.
When the read address is acknowledged, the ADC outputs two
bytes of conversion data. The first byte contains four status bits
and the four MSBs of the conversion result. The status bits
contain two leading 0s and two channel-identifier bits. After
this first byte, the AD7991/AD7995/AD7999 outputs the
second byte of the conversion result. For the AD7991, this
second byte contains the lower eight bits of conversion data. For
the AD7995, this second byte contains six bits of conversion
data plus two trailing 0s. For the AD7999, this second byte
contains four bits of conversion data and four trailing 0s.
The master then sends a NO ACK to the AD7991/AD7995/
AD7999, as long as no further reads are required. If the master
instead sends an ACK to the AD7991/AD7995/AD7999, the
ADC powers up and completes another conversion. When
more than one channel bit has been set in the configuration
register, this conversion is performed on the second channel in
the selected sequence. If only one channel is selected, the ADC
converts again on the selected channel.
06
46
1-
02
9
Sr
RA
A
SECOND DATA BYTE
(LSB)
FIRST DATA BYTE
(MSB)
7-BIT ADDRESS
SCL
SDA
A
11
9
Sr/P
ACK. BY
ADC
ACK. BY
MASTER
NO ACK. BY
MASTER
Figure 28. Mode of Operation, Single-Channel Conversion
相關PDF資料
PDF描述
LT1671IS8#TR IC COMPARATOR 60NS LOW PWR 8SOIC
LTC1441IS8#PBF IC COMP W/REF LP DUAL 8-SOIC
LTC1441IS8 IC COMP W/REF LP DUAL 8-SOIC
CS5550-ISZ IC ADC 2CH LOW-COST 24SSOP
VE-2W0-MY-B1 CONVERTER MOD DC/DC 5V 50W
相關代理商/技術參數
參數描述
AD7991YRJZ-1RL 功能描述:IC ADC 12BIT 4CH I2C SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率(每秒):15 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:1 功率耗散(最大):480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN(5x7) 包裝:帶卷 (TR) 輸入數目和類型:16 個單端,雙極;8 個差分,雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7992 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel, 12-Bit ADC with I2C Compatible Interface in 10-Lead MSOP
AD7992_05 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel, 12-Bit ADC with I2C-Compatible
AD7992BRM-0 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 10-Pin MSOP
AD7992BRM-0REEL 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 10-Pin MSOP T/R