參數資料
型號： AD7949BCPZRL7
廠商： Analog Devices Inc
文件頁數： 5/32頁
文件大?。?/td> 0K
描述： IC ADC 14BIT 250KSPS 8CH 20LFCSP
產品培訓模塊： Power Line Monitoring
產品變化通告： Startup Circuitry Design Improvement Change 15/April/2009
標準包裝： 1,500
系列： PulSAR®
位數： 14
采樣率（每秒）： 250k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 15.5mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 20-VFQFN 裸露焊盤，CSP
供應商設備封裝： 20-LFCSP-VQ
包裝： 帶卷 (TR)
輸入數目和類型： *
Data Sheet
AD7949
Rev. D | Page 13 of 32
TERMINOLOGY
Least Significant Bit (LSB)
The LSB is the smallest increment that can be represented by a
converter. For an analog-to-digital converter with N bits of
resolution, the LSB expressed in volts is
N
REF
V
LSB
2
(V) =
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 24).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level LSB above analog
ground. The offset error is the deviation of the actual transition
from that point.
Gain Error
The last transition (from 111 … 10 to 111 … 11) should occur
for an analog voltage 1 LSB below the nominal full scale. The
gain error is the deviation in LSB (or percentage of full-scale
range) of the actual level of the last transition from the ideal
level after the offset error is adjusted out. Closely related is the
full-scale error (also in LSB or percentage of full-scale range),
which includes the effects of the offset error.
Aperture Delay
Aperture delay is the measure of the acquisition performance. It
is the time between the rising edge of the CNV input and the
point at which the input signal is held for a conversion.
Transient Response
Transient response is the time required for the ADC to accurately
acquire its input after a full-scale step function is applied.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the total rms noise measured with the inputs shorted together.
The value for dynamic range is expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in decibels.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in decibels.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels, between the rms amplitude
of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD by the formula
ENOB = (SINADdB 1.76)/6.02
and is expressed in bits.
Channel-to-Channel Crosstalk
Channel-to-channel crosstalk is a measure of the level of crosstalk
between any two adjacent channels. It is measured by applying a
dc to the channel under test and applying a full-scale, 100 kHz
sine wave signal to the adjacent channel(s). The crosstalk is the
amount of signal that leaks into the test channel and is expressed
in decibels.
Reference Voltage Temperature Coefficient
Reference voltage temperature coefficient is derived from the
typical shift of output voltage at 25°C on a sample of parts at the
maximum and minimum reference output voltage (VREF) measured
at TMIN, T (25°C), and TMAX. It is expressed in ppm/°C as
6
10
)
–
(
)
(
)
(
–
)
(
)
C
ppm/
(
×
°
=
°
MIN
MAX
REF
T
C
25
V
Min
V
Max
V
TCV
where:
VREF (Max) = maximum VREF at TMIN, T (25°C), or TMAX.
VREF (Min) = minimum VREF at TMIN, T (25°C), or TMAX.
VREF (25°C) = VREF at 25°C.
TMAX = +85°C.
TMIN = –40°C.
相關PDF資料
PDF描述
AD7951BSTZRL IC ADC 14BIT 1MSPS 48-LQFP
AD7952BCPZ IC ADC 14BIT DIFF 1MSPS 48LFCSP
AD7980ARMZ ADC 16BIT 1MSPS LP 10-MSOP
AD7982BCPZ-RL IC ADC 18BIT 1MSPS PULSAR 10LFCS
AD7983BCPZ-RL7 IC ADC 16BIT 1.33MSPS 10LFCSP
相關代理商/技術參數
參數描述
AD7949SCPZ-EP-R2 功能描述:14 Bit Analog to Digital Converter 8 Input 1 SAR 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:PulSAR? 包裝:剪切帶（CT） 零件狀態:有效 位數:14 采樣率（每秒）:256k 輸入數:8 輸入類型:差分，單端 數據接口:SPI，DSP 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:1 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:2.3 V ~ 5.5 V 電壓 - 電源，數字:2.3 V ~ 5.5 V 特性:溫度傳感器 工作溫度:-55°C ~ 125°C 封裝/外殼:20-WFQFN 裸露焊盤，CSP 供應商器件封裝:20-LFCSP-WQ（4x4） 標準包裝:1
AD7949SCPZ-EP-RL7 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 14-bit Serial 20-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:8 CH 250KSPS 14BIT ADC IC - Tape and Reel 制造商:Analog Devices 功能描述:IC ADC 14BIT 8CH 250KSPS 20LFCSP 制造商:Analog Devices 功能描述:Analog to Digital Converters - ADC 14-Bit 8CH 250 kSPS 制造商:Analog Devices 功能描述:CONVERTER - ADC
AD795 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp
AD795_02 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp
AD795_09 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*