參數資料
型號： AD7938BSUZ
廠商： Analog Devices Inc
文件頁數： 7/36頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 8CHAN 32TQFP
標準包裝： 1
位數： 12
采樣率（每秒）： 1.5M
數據接口： 并聯
轉換器數目： 1
功率耗散（最大）： 13.5mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-TQFP
供應商設備封裝： 32-TQFP（7x7）
包裝： 托盤
輸入數目和類型： 8 個單端，單極；4 個差分，單極；4 個偽差分，單極；7 偽差分，單極
配用： EVAL-AD7938CBZ-ND - EVAL BOARD FOR AD7938
Data Sheet
AD7938/AD7939
Rev. C | Page 15 of 36
ON-CHIP REGISTERS
The AD7938/AD7939 have two on-chip registers that are
necessary for the operation of the device. These are the control
register, which is used to set up different operating conditions,
and the shadow register, which is used to program the analog
input channels to be converted.
CONTROL REGISTER
The control register on the AD7938/AD7939 is a 12-bit, write-
only register. Data is written to this register using the CS and
WR pins. The control register is shown in Table 7 and the
functions of the bits are described in Table 8. At power up, the
default bit settings in the control register are all 0s.
Table 7. Control Register Bits
MSB
LSB
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
PM1
PM0
CODING
REF
ADD2
ADD1
ADD0
MODE1
MODE0
SHDW
SEQ
RANGE
Table 8. Control Register Bit Function Description
Bit No.
Mnemonic
Description
11, 10
PM1, PM0
Power Management Bits. These two bits are used to select the power mode of operation. The user can choose
between either normal mode or various power-down modes of operation, as shown in Table 9.
9
CODING
This bit selects the output coding of the conversion result. If this bit is set to 0, the output coding is straight
(natural) binary. If this bit is set to 1, the output coding is twos complement.
8
REF
This bit selects whether the internal or external reference is used to perform the conversion. If this bit is Logic 0, an
external reference should be applied to the VREF pin. If this bit is Logic 1, the internal reference is selected. See the
7 to 5
ADD2 to
ADD0
These three address bits are used to either select which analog input channel is converted in the next conversion if
the sequencer is not used, or to select the final channel in a consecutive sequence when the sequencer is used, as
described in Table 11. The selected input channel is decoded as shown in Table 10.
4, 3
MODE1,
MODE0
The two mode pins select the type of analog input on the eight VIN pins. The AD7938/AD7939 can have either eight
single-ended inputs, four fully differential inputs, four pseudo differential inputs, or seven pseudo differential
inputs. See Table 10.
2
SHDW
The SHDW bit in the control register is used in conjunction with the SEQ bit to control the sequencer function and
access the SHDW register. See Table 11.
1
SEQ
The SEQ bit in the control register is used in conjunction with the SHDW bit to control the sequencer function and
access the SHDW register. See Table 11.
0
RANGE
This bit selects the analog input range of the AD7938/AD7939. If it is set to 0, the analog input range extends from
0 V to VREF. If it is set to 1, the analog input range extends from 0 V to 2 × VREF. When this range is selected, VDD must
be 4.75 V to 5.25 V if a 2.5 V reference is used; otherwise, care must be taken to ensure that the analog input remains
within the supply rails. See the Analog Inputs section for more information.
Table 9. Power Mode Selection Using the Power Management Bits in the Control Register
PM1
PM0
Mode
Description
0
Normal Mode
When operating in normal mode, all circuitry is fully powered up at all times.
0
1
Autoshutdown
When operating in autoshutdown mode, the AD7938/AD7939 enter full shutdown mode at the end of
each conversion. In this mode, all circuitry is powered down.
1
0
Autostandby
When the AD7938/AD7939 enter this mode, all circuitry is powered down except for the reference and
reference buffer. This mode is similar to autoshutdown mode, but it allows the part to power up in 7 s (or
600 ns if an external reference is used). See the Power Modes of Operation section for more information.
1
Full Shutdown
When the AD7938/AD7939 enter this mode, all circuitry is powered down. The information in the control
register is retained.
相關PDF資料
PDF描述
VI-B41-MW CONVERTER MOD DC/DC 12V 100W
AD7650ASTZ IC ADC 16BIT 570KSPS 48LQFP
AD7694BRMZ IC ADC 16BIT SRL 250KSPS 8MSOP
VI-2TR-MX CONVERTER MOD DC/DC 7.5V 75W
ISL3152EIUZ-T7A IC LINEAR
相關代理商/技術參數
參數描述
AD7938BSUZ6 制造商:AD 功能描述:Pb Free
AD7938BSUZ-6 功能描述:IC ADC 12BIT 8CHAN 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD7938BSUZ-6REEL7 功能描述:IC ADC 12BIT 8CHAN 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7938BSUZ-REEL7 功能描述:IC ADC 12BIT 8CHAN 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD7939 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*