- 您現在的位置：買賣IC網 > PDF目錄10687 > AD7923BRUZ (Analog Devices Inc)IC ADC 12BIT 4CH W/SEQ 16TSSOP PDF資料下載
參數資料
| 型號： | AD7923BRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 4CH W/SEQ 16TSSOP |
| 標準包裝： | 96 |
| 位數： | 12 |
| 采樣率（每秒）： | 200k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 7.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極 |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7923CBZ-ND - BOARD EVAL FOR AD7923 |
AD7923
Data Sheet
Rev. D | Page 18 of 24
Only a portion of the cycle time is taken up by the conversion
time and the dummy transfer for wakeup. In this mode, the
power con-sumption of the part is greatly reduced because the
part enters shutdown at the end of each conversion. When the
control register is programmed to move into auto shutdown, it
does so at the end of the conversion. The user can move the
ADC in and out of the low power state by controlling the CS
signal.
POWERING UP THE AD7923
When supplies are first applied to the AD7923, the ADC can
power up in any of the operating modes of the part. To ensure
that the part is placed into the required operating mode, the
user should perform a dummy cycle operation, as outlined in
Figure 23 through Figure 25.
The dummy conversion operation must be performed to place
the part into the desired mode of operation. To ensure that the
part is in normal mode, this dummy cycle operation can be
performed with the DIN line tied high, that is, PM1, PM0 = 1, 1
(depending on other required settings in the control register),
but the minimum power-up time of 1 s must be allowed from
the rising edge of CS, where the control register is updated,
before attempting the first valid conversion. This is to allow for
the possibility that the part initially powered up in shutdown.
If the desired mode of operation is full shutdown, then again
only one dummy cycle is required after supplies are applied. In
this dummy cycle, the user simply sets the power management
bits, PM1, PM0 = 1, 0, and upon the rising edge of CS at the
end of that serial transfer, the part enters full shutdown. If the
desired mode of operation is auto shutdown after supplies are
applied, two dummy cycles are required, the first with DIN tied
high and the second dummy cycle to set the power manage-
ment bits PM1 and PM0 = 0,1. On the second CS rising edge
after the supplies are applied, the control register contains the
correct information and the part enters auto shutdown mode as
programmed. If power consumption is of critical concern, then
in the first dummy cycle the user may set PM1, PM0 = 1, 0, that
is, full shutdown, and then place the part into auto shutdown in
the second dummy cycle. For illustration purposes, Figure 25 is
shown with DIN tied high on the first dummy cycle in this case.
Figure 23, Figure 24, and Figure 25 each show the required
dummy cycle(s) after supplies are applied in the case of normal
mode, full shutdown mode, and auto shutdown mode, respect-
ively, being the desired mode of operation.
CS
SCLK
DOUT
DIN
1
14
16
1
14
16
PART IS IN FULL
SHUTDOWN
PART BEGINS TO POWER UP ON
CS RISING EDGE AS PM1 = PM0 =1
THE PART IS FULLY POWERED UP
ONCE
tPOWER UP HAS ELAPSED
CONTROL REGISTER IS LOADED ON THE
FIRST 12 CLOCKS. PM1 = 1, PM0 = 1
TO KEEP THE PART IN NORMAL MODE, LOAD
PM1 = PM0 = 1 IN CONTROL REGISTER
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
DATA INTO CONTROL REGISTER
t12
03086-021
Figure 21. Full Shutdown Mode Operation
1
CS
SCLK
DOUT
DIN
16
1
16
1
16
DUMMY CONVERSION
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
INVALID DATA
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
CONTROL REGISTER IS LOADED ON THE
FIRST 12 CLOCKS, PM1 = 0, PM0 = 1
CONTROL REGISTER CONTENTS SHOULD
NOT CHANGE, WRITE BIT = 0
TO KEEP PART IN THIS MODE, LOAD PM1 = 0, PM0 = 1
IN CONTROL REGISTER OR SET WRITE BIT = 0
PART IS FULLY
POWERED UP
PART BEGINS
TO POWER
UP ON CS
FALLING EDGE
PART ENTERS
SHUTDOWN ON CS
RISING EDGE AS
PM1 = 0, PM0 =1
12
PART ENTERS
SHUTDOWN ON CS
RISING EDGE AS
PM1 = 0, PM0 =1
DATA INTO CONTROL REGISTER
03086-022
Figure 22. Auto Shutdown Mode Operation
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1442IN8 | IC COMP W/REF LP DUAL 8-DIP |
| LTC2484IDD#PBF | IC ADC 24BIT 10-DFN |
| LTC2485IDD#PBF | IC ADC 24BIT I2C 10-DFN |
| LTC1443CDHD#TRPBF | IC COMP W/REF LOW PWR QUAD 16DFN |
| LTC1444CDHD#TRPBF | IC COMP QD LP 1.221VREF 16-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7923BRUZ-REEL | 功能描述:IC ADC 12BIT 4CH W/SEQ 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7923BRUZ-REEL7 | 功能描述:IC ADC 12BIT 4CH W/SEQ 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7923SRU-EP | 功能描述:模數轉換器 - ADC 4CH 200 kSPS 12-Bit W/ Sequencer RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD7923SRU-EP-RL7 | 功能描述:模數轉換器 - ADC 4CH 200 kSPS 12-Bit W/ Sequencer RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD7923WYRUZ-REEL7 | 功能描述:IC ADC 12BIT 4CH W/SEQ 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。