參數資料
型號： AD7921ARMZ
廠商： Analog Devices Inc
文件頁數： 10/28頁
文件大小： 0K
描述： IC ADC 12BIT DUAL LP 8-MSOP
標準包裝： 50
位數： 12
采樣率（每秒）： 250k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 20mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 管件
輸入數目和類型： 2 個單端，單極
產品目錄頁面： 779 (CN2011-ZH PDF)
AD7911/AD7921
Rev. A | Page 18 of 28
MODES OF OPERATION
The two modes of operation of the AD7911/AD7921 are
normal mode and power-down mode. The mode of operation is
selected by controlling the logic state of the CS signal. The point
at which CS is pulled high after the conversion has been initi-
ated determines whether the AD7911/AD7921 enter power-
down mode. Similarly, if already in power-down mode, CS can
control whether the device returns to normal operation or
remains in power-down mode.
Power-down mode is designed to provide flexible power
management options and to optimize the ratio of power
dissipation to throughput rate for different application
requirements.
NORMAL MODE
Normal mode is intended for the fastest throughput rate
performance. The user does not have to worry about any
power-up time, because the AD7911/AD7921 remain fully
powered all the time. Figure 26 shows the operation of the
AD7911/AD7921 in this mode.
The conversion is initiated on the falling edge of CS, as
described in the
section. To ensure that the part
remains fully powered up at all times,
CS must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
of CS. If CS is brought high any time after the 10th SCLK falling
edge but before the end of tCONVERT, the part remains powered-
up, but the conversion is terminated and DOUT goes back into
three-state. For the AD7911/AD7921, a minimum of 14 and
16 serial clock cycles, respectively, are needed to complete the
conversion and access the complete conversion result.
CS can idle high until the next conversion or can idle low until
CS returns high sometime prior to the next conversion
(effectively idling CS low). Once a data transfer is complete
(DOUT has returned to three-state), another conversion can be
initiated after the quiet time, tQUIET, has elapsed by bringing CS
low again.
POWER-DOWN MODE
Power-down mode is intended for use in applications where
slower throughput rates are required. Either the ADC is
powered down between each conversion, or a series of
conversions can be performed at a high throughput rate and
then the ADC is powered down for a relatively long duration
between these bursts of several conversions. When the
AD7911/AD7921 are in power-down mode, all analog circuitry
is powered down.
To enter power-down mode, the conversion process must be
interrupted by bringing CS high any time after the second
falling edge of SCLK and before the 10th falling edge of SCLK,
as shown in
. Once
CS has been brought high in this
window of SCLKs, then the part enters power-down mode, the
conversion that was initiated by the falling edge of CS is
terminated, and DOUT goes back into three-state. If CS is
brought high before the second SCLK falling edge, then the part
remains in normal mode and does not power down. This helps
to avoid accidental power-down due to glitches on the CS line.
To exit this mode of operation and power the AD7911/AD7921
up again, a dummy conversion is performed. On the falling
edge of CS, the device begins to power up and continues to
power up as long as CS is held low until after the falling edge of
the 10th SCLK. The device is fully powered up once 16 SCLKs
have elapsed and valid data results from the next conversion, as
shown in
. If
CS is brought high before the 10th falling
edge of SCLK, then the AD7911/AD7921 go back into power-
down mode. This helps to avoid accidental power-up due to
glitches on the CS line or an inadvertent burst of 8 SCLK cycles
while CS is low. Therefore, although the device might begin to
power up on the falling edge of CS, it powers down again on the
rising edge of CS, as long as this occurs before the 10th SCLK
falling edge.
04350-0-025
CS
1
10
12
14
16
1
10
12
14
16
AD7911/AD7921
SCLK
DIN
DOUT
CHANNEL FOR NEXT CONVERSION
CONVERSION RESULT
Figure 26. Normal Mode Operation
相關PDF資料
PDF描述
AD7920BRMZ IC ADC 12BIT 250KSPS 8-MSOP
LTC1442IN8#PBF IC COMP W/REF LP DUAL 8-DIP
LT1394CS8#TRPBF IC COMPARATOR LOW PWR 7NS 8-SOIC
LTC1442IS8 IC COMP W/REF LP DUAL 8-SOIC
AD7788BRMZ IC ADC 16BIT LP 10-MSOP
相關代理商/技術參數
參數描述
AD7921ARMZ-REEL 功能描述:IC ADC 12BIT DUAL LP 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD7921ARMZ-REEL7 功能描述:IC ADC 12BIT DUAL LP 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7921AUJ-R2 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT , 250KSPS ADC I.C. - Bulk
AD7921AUJ-REEL7 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 8-Pin TSOT T/R
AD7921AUJZ-R2 功能描述:IC ADC 12BIT DUAL LP TSOT-23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*