參數資料
型號： AD7894BR-2
英文描述： Analog-to-Digital Converter， 14-Bit
中文描述： 模擬到數字轉換器，14位
文件頁數： 15/20頁
文件大?。?/td> 191K
代理商： AD7894BR-2
REV. B
AD7890
–15–
SIMPLIFYING THE INTERFACE
To minimize the number of interconnect lines to the AD7890,
the user can connect the
RFS
and
TFS
lines of the AD7890
together and read and write from the part simultaneously. In
this case, new control register data should be provided on the
DATA IN line selecting the input channel and possibly providing
a conversion start command while the part provides the result
from the conversion just completed on the DATA OUT line.
In the self-clocking mode, this means that the part provides all
the signals for the serial interface. It does require that the micro-
processor has the data to be written to the Control Register
available in its output register when the part brings the
TFS
line
low. In the external clocking mode, it means that the user only
has to supply a single frame synchronization signal to control
both the read and write operations.
Care must be taken with this scheme that the read operation is
completed before the next conversion starts if the user wants to
obtain optimum performance from the part. In the case of the
software conversion start, the conversion command is written to
the Control Register on the sixth serial clock edge. However, the
read operation continues for another 10 serial clock cycles. To
avoid reading during the sampling instant or during conversion,
the user should ensure that the internal pulsewidth is sufficiently
long (by choosing C
EXT
) so that the read operation is completed
before the next conversion sequence begins. Failure to do this
will result in significantly degraded performance from the part,
both in terms of signal-to-noise ratio and dc parameters. In the
case of a hardware conversion start, the user should ensure that
the delay between the sixth falling edge of the serial clock in the
write operation and the next rising edge of
CONVST
is greater
than the internal pulsewidth.
MICROPROCESSOR/MICROCONTROLLER INTERFACE
The AD7890’s flexible serial interface allows for easy connec-
tion to the serial ports of DSP processors and microcontrollers.
Figures 12 through 15 show the AD7890 interfaced to a num-
ber of different microcontrollers and DSP processors. In some
of the interfaces shown, the AD7890 is configured as the master
in the system, providing the serial clock and frame sync for the
read operation while in others it acts as a slave with these signals
provided by the microprocessor.
AD7890–8051 Interface
Figure 12 shows an interface between the AD7890 and the
8xC51 microcontroller. The AD7890 is configured for its exter-
nal clocking mode while the 8xC51 is configured for its Mode 0
serial interface mode. The diagram shown in Figure 12 makes
no provisions for monitoring when conversion is complete on
the AD7890 (assuming hardware conversion start is used). To
monitor the conversion time on the AD7890 a scheme such as
outlined previously with
CONVST
can be used. This can be
implemented in two ways. One is to connect the
CONVST
line
to another parallel port bit which is configured as an input. This
port bit can then be polled to determine when conversion is
complete. An alternative is to use an interrupt driven system in
which case the
CONVST
line should be connected to the
INT1
input of the 8XC51.
Since the 8xC51 contains only one serial data line, the DATA
OUT and DATA IN lines of the AD7890 must be connected
together. This means that the 8xC51 cannot communicate with
the output register and Control Register of the AD7890 at the
same time. The 8xC51 outputs the LSB first in a write opera-
tion so care should be taken in arranging the data which is to be
transmitted to the AD7890. Similarly, the AD7890 outputs the
MSB first during a read operation while the 8xC51 expects the
LSB first. Therefore, the data that is to be read into the serial
port needs to be rearranged before the correct data word from
the AD7890 is available in the microcontroller.
The serial clock rate from the 8xC51 is limited to significantly
less than the allowable input serial clock frequency with which
the AD7890 can operate. As a result, the time to read data from
the part will actually be longer than the conversion time of the
part. This means that the AD7890 cannot run at its maximum
throughput rate when used with the 8xC51.
AD7890
V
DD
SMODE
RFS
TFS
DATA OUT
DATA IN
SCLK
8xC51
P1.0
P1.1
P3.0
P3.1
Figure 12. AD7890 to 8xC51 Interface
TFS
(I)
SCLK (I)
DATA IN (I)
A2
A1
A0
NOTE:
(I) SIGNIFIES AN INPUT; (O) SIGNIFIES AN OUTPUT.
CONV
STBY
DON
’
T
CARE
DON
’
T
CARE
DON
’
T
CARE
t
20
t
21
t
22
t
23
Figure 11. External Clocking (Slave) Mode Control Register Write
相關PDF資料
PDF描述
AD7899AR-1 Analog-to-Digital Converter， 14-Bit
AD7899AR-2 12-Bit Rail-to-Rail Micropower DACs in SO-8; Package: PDIP; No of Pins: 8; Temperature Range: -40°C to +85°C
AD7899AR-3 Dual 12-Bit Rail-to-Rail Micropower DACs; Package: SO; No of Pins: 16; Temperature Range: 0°C to +70°C
AD7899ARS-1 Dual 12-Bit Rail-to-Rail Micropower DACs; Package: SO; No of Pins: 16; Temperature Range: -40°C to +85°C
AD7899ARS-2 Analog-to-Digital Converter， 14-Bit
相關代理商/技術參數
參數描述
AD7894BR-3 功能描述:IC ADC 14BIT SRL T/H LP 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD7894BR-3REEL 功能描述:IC ADC 14BIT SRL T/H LP 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD7894BR-3REEL7 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 14-bit Serial 8-Pin SOIC N T/R
AD7894BRZ-10 功能描述:IC ADC 14BIT SRL T/H LP 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7894BRZ-10REEL 功能描述:IC ADC 14BIT SRL T/H LP 8SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*