參數資料
型號: AD7880CNZ
廠商: Analog Devices Inc
文件頁數: 15/16頁
文件大?。?/td> 0K
描述: IC ADC 12BIT MONO LOW PWR 24DIP
標準包裝: 15
位數: 12
采樣率(每秒): 66k
數據接口: 并聯
轉換器數目: 1
功率耗散(最大): 50mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 通孔
封裝/外殼: 24-DIP(0.300",7.62mm)
供應商設備封裝: 24-PDIP
包裝: 管件
輸入數目和類型: 2 個單端,單極;2 個單端,雙極
AD7880
–8–
REV. 0
12
11.5
11
10.5
10
INPUT FREQUENCY – kHz
SAMPLE FREQUENCY = 61kHz
T = 25 C
A
15
30.5
EFFECTIVE
NUMBER
OF
BITS
Figure 13. Effective Number of Bits vs. Frequency
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the rms value
of the fundamental. For the AD7880, THD is defined as:
THD
= 20 log
V
2
2 +V
3
2 +V
4
2 +V
5
2 +V
6
2
V
1
(3)
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5 and V6 are the rms amplitudes of the second through the
sixth harmonic. The THD is also derived from the FFT plot of
the ADC output spectrum.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
± nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for which
neither m nor n are equal to zero. For example, the second or-
der terms include (fa + fb) and (fa – fb), while the third order
terms include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb).
Using the CCIF standard where two input frequencies near the
top end of the input bandwidth are used, the second and third
order terms are of different significance. The second order terms
are usually distanced in frequency from the original sine waves,
while the third order terms are usually at a frequency close to
the input frequencies. As a result, the second and third order
terms are specified separately. The calculation of the inter-
modulation distortion is as per the THD specification where it is
the ratio of the rms sum of the individual distortion products to
the rms amplitude of the fundamental expressed in dBs. In this
case, the input consists of two, equal amplitude, low distortion,
sine waves. Figure 14 shows a typical IMD plot for the
AD7880.
Figure 14. IMD Plot
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to FS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification will be
determined by the largest harmonic in the spectrum, but for
parts where the harmonics are buried in the noise floor the peak
will be a noise peak.
相關PDF資料
PDF描述
VE-26K-MX-F2 CONVERTER MOD DC/DC 40V 75W
VI-24B-IU-F4 CONVERTER MOD DC/DC 95V 200W
D38999/26FC8PE CONN PLUG 8POS STRAIGHT W/PINS
IDT72215LB15TFI8 IC FIFO 512X18 SYNC 15NS 64QFP
VI-23M-IX-B1 CONVERTER MOD DC/DC 10V 75W
相關代理商/技術參數
參數描述
AD7880CQ 制造商:Analog Devices 功能描述:ADC Single SAR 66ksps 12-bit Parallel 24-Pin CDIP 制造商:Rochester Electronics LLC 功能描述:12 BIT ADC IC - Bulk
AD7880CR 功能描述:IC ADC 12BIT MONO LP 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD7880CR-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 66ksps 12-bit Parallel 24-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 66KSPS 12-BIT PARALLEL 24SOIC W - Tape and Reel
AD7880CRZ 功能描述:IC ADC 12BIT MONO LP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7880CRZ-REEL 功能描述:IC ADC 12BIT MONO LP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極