- 您現在的位置：買賣IC網 > PDF目錄373922 > AD7878SQ (ANALOG DEVICES INC) IC 1:10 CLOCK DRIVER 20-QSOP PDF資料下載
參數資料
| 型號： | AD7878SQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | IC 1:10 CLOCK DRIVER 20-QSOP |
| 中文描述： | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDIP28 |
| 封裝： | HERMETIC SEALED, CERDIP-28 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 417K |
| 代理商： | AD7878SQ |
AD7878
–12–
REV. A
The MC68000
AS
and R/
W
outputs are used to generate sepa-
rate
DMWR
and
DMRD
inputs for the AD7878. As with the
three interfaces previously described, WAIT states are inserted if
a read/write operation is attempted while the track/hold amplifier
is going from the track to the hold mode.
Figure 21. AD7878–MC68000 Interface
Typical AD7878 Microprocessor Operating Sequence
After power-up or reset, the status/control register is initialized
by writing to the AD7878. This enables the
ALFL
output if
required for a microprocessor interrupt and sets the effective word
length of the FIFO memory. The processor now executes the
main body of the program while waiting for an ADC interrupt.
This interrupt will occur when the preprogrammed number of
samples are collected in the FIFO memory. The interrupt ser-
vice routine first interrogates DB5(FOOR) of the status/control
register to determine if any sample in the FIFO memory is out
of range. If all data samples are valid, then the program pro-
ceeds to read the FIFO memory. If, on the other hand, at least
one sample is out of range, then an overrange routine is called.
There are many actions that can be taken by the out of range
routine, the selection of which is application dependent. One
option is to ignore all the current samples residing in the FIFO
memory, reinitialize the status/control register and return to the
main body of the program. Another option is to check the indi-
vidual out of range status of each word in the FIFO memory
and to discard the invalid ones. The underrange or overrange
status of each word can also be determined and the analog input
adjusted accordingly before returning to the main program.
Note: there is no need to check the out-of-range status if the
analog input is always assured to be within range.
THROUGHPUT RATE
The AD7878 has a maximum specified throughput rate (sample
rate) of 100 kHz. This is a worst-case test condition and specifi-
cations apply for reduced sampling rates, provided that Nyquist
criterion is obeyed. The throughput rate must take into account
ADC
CONVST
pulse width, ADC conversion time and the
track/hold amplifier acquisition time. The time required for each
of these tasks is shown in Table II for a selection of DSP proces-
sors. Since the ADC clock has to be synchronized to the micro-
processor dock, the conversion time depends on the micro-
processor used. In addition, time must be allowed for reading data
from the AD7878. If this task is performed during the track/
hold amplifier acquisition period, then it does not impact the
overall throughput rate. However, if the read operations occur
during a conversion, they may stretch the conversion time and
reduce the track/hold amplifier acquisition time. The track/hold
amplifier requires a minimum of 2
μ
s to operate to specification.
The time required to read from the AD7878 depends on the
number of FIFO memory locations to be read and the software
organization.
As an example, consider an application using the ADSP-2100
and the AD7878 with a throughput rate of 100 kHz. The time
required for the
CONVST
pulse and the ADC conversion is
7.375
μ
s. This leaves 2.625
μ
s for the track/hold acquisition
time and for reading the ADC (both operations occurring in
parallel). The ADSP-2100, when operating from a 32 MHz
clock, has an instruction cycle of 125 ns and an interrupt re-
sponse time of 500 ns. This allows adequate time to perform
16 read operations within the time budget allowed.
Table II. AD7878 Throughput Rate
CONVST
Pulse Width
Conversion
Time
T/H Acquisition
Time
Number of
Clock Cycles
ADSP-2100
1
TMS32010
2
TMS32020
2
Non-
Applicable
2 min
250 ns min
400 ns min
400 ns min
57 max
7.125
μ
s max 2
μ
s min
11.14
μ
s max 2
μ
s min
11.14
μ
s max 2
μ
s min
NOTES
1
ADSP-2100 Clock Frequency = 32 MHz.
2
TMS320XX Clock Frequency = 20 MHz.
APPLICATION HINTS
Good printed circuit board (PCB) layout is as important as the
overall circuit design itself in achieving high speed A/D perfor-
mance. The AD7878 is required to make bit decisions on an
LSB size of 1.465 mV. To achieve this, the designer has to be
conscious of noise both in the ADC itself and in the preceding
analog circuitry. Switching mode power supplies are not recom-
mended as the switching spikes will feed through to the com-
parator, causing noisy code transitions. Other concerns are
ground loops and digital feedthrough from microprocessors.
These factors influence any ADC, and a proper PCB layout that
minimizes these effects is essential for best performance.
LAYOUT HINTS
Ensure that the layout for the printed circuit board has the
digital and analog signal lines separated as much as possible.
Take care not to run any digital track alongside an analog signal
track. Guard (screen) the analog input with AGND.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7878 | LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878AQ | LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878BQ | LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878KN | LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878KP | LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7878SQ/883B | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin CDIP 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 12-BIT PARALLEL 28CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12-BIT ADC IC - Bulk 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC COMPLETE 12-BIT ADC IC |
| AD7879 | 制造商:Analog Devices 功能描述:LOW COST CONTROLLER FOR TOUCH SCREENS - Rail/Tube |
| AD7879-1ACBZ-500R7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Voltage Controller for Touch Screens |
| AD7879-1ACBZ-RL | 制造商:Analog Devices 功能描述: |
| AD7879-1ACPZ-500R7 | 功能描述:IC ADC 12BIT CTRLR TOUCH 16LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。