- 您現在的位置：買賣IC網 > PDF目錄373922 > AD7878LN (ANALOG DEVICES INC) SOTiny Low-Voltage, 8-Ohm Single Analog / Bus Switch PDF資料下載
參數資料
| 型號： | AD7878LN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | SOTiny Low-Voltage, 8-Ohm Single Analog / Bus Switch |
| 中文描述： | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 417K |
| 代理商： | AD7878LN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
AD7878
–8–
REV. A
Extended Read/Write Operation
As described earlier, a read/write operation to the AD7878 can
cause spurious on-chip transients. Should these transients occur
while the track/hold is going from track to hold mode, it may
result in an incorrect value of V
IN
being held by the track/hold
amplifier. Because the
CONVST
input has asynchronous capa-
bility, a read/write operation could occur while
CONVST
is
low. The AD7878 allows the read/write operation to occur but
has the facility to disable its three-state drivers so that there is
no data bus activity and, hence, no transients while the track/
hold goes from track to hold.
Writing a logic 0 to DB5 (
DISO
) of the status/control register
prevents the output latches from being enabled while the
AD7878
BUSY
signal is low. If a microprocessor read/write
operation can occur during the
BUSY
low time, the
BUSY
should be gated with
CS
of the AD7878 and this gated signal
used to stretch the instruction cycle using DMACK (ADSP-
2100), READY (TMS32020) or
DTACK
(68000).
When
CONVST
goes low, the AD7878 acknowledges it by
bringing
BUSY
low on the next rising edge of CLK IN. With a
logic 0 in DB5, the AD7878 data bus cannot now be enabled. If
a read/write operation now occurs, the
BUSY
and
CS
gated
signal drives the microprocessor into a WAIT state, thereby
extending the read/write operation.
BUSY
goes high on the
second rising edge of CLK IN after
CONVST
goes high. The
AD7878 data outputs are now enabled and the microprocessor
is released from its WAIT state, allowing it to complete its read/
write operation to the AD7878.
The microprocessor cycle time for the read/write operation is
extended by the
CONVST
pulse width plus two CLK IN peri-
ods worst case. This is the maximum length of time for which
BUSY
can be low. Assuming a
CONVST
pulse width of two
CLK IN periods and an 8 MHz CLK IN, the instruction cycle
is extended by 500 ns maximum. Figure 9 shows the timing
diagram for an extended read operation. In a similar manner, a
write operation will be extended if it occurs during a
CONVST
pulse.
For processors that cannot be forced into a WAIT state, writing
a logic 1 into DB5 of the status/control register allows the out-
put latches to be enabled while
BUSY
is low. In this case
BUSY
still goes low as before, but it would not be used to stretch the
read/write cycle and the instruction cycle continues as normal
(see Figures 6 and 8).
Figure 9. Extended Read Operation
AD7878 DYNAMIC SPECIFICATIONS
The AD7878 is specified and 100% tested for dynamic perfor-
mance specifications rather than for traditional dc specifications
such as Integral and Differential Nonlinearity. These ac specifi-
cations provide information on the AD7878’s effect on the spec-
tral content of the input signal. Hence, the parameters for which
the AD7878 is specified include SNR, Harmonic Distortion, inter-
modulation Distortion and Peak Harmonics. These terms are dis-
cussed in more detail in the following sections.
Signal-to-Noise Ratio (SNR)
SNR is the measured signal-to-noise ratio at the output of the
ADC. The signal is the rms magnitude of the fundamental.
Noise is the rms sum of all the nonfundamental signals (excluding
dc) up to half the sampling frequency (f
S
/2). SNR is dependent
upon the number of quantization levels used in the digitization
process; the more levels, the smaller the quantization noise. The
theoretical signal-to-noise ratio for a sine wave input is given by
SNR =
(6.02
N
+ 1.76)
dB
where
N
is the number of bits. Thus for an ideal 12-bit con-
verter,
SNR
= 74 dB.
The output spectrum from the ADC is evaluated by applying a
sine-wave signal of very low distortion to the V
IN
input, which is
sampled at a 100 kHz sampling rate. A Fast Fourier Transform
(FFT) plot is generated from which the SNR data can be ob-
tained. Figure 10 shows a typical 2048 point FFT plot of the
AD7878KN with an input signal of 25 kHz and a sampling
frequency of 100 kHz. The SNR obtained from this graph is
72.6 dB. It should be noted that the harmonics are included in
the SNR calculation.
(1)
Figure 10. AD7878 FFT Plot
Effective Number of Bits
The formula given in (1) relates the SNR to the number of bits.
Rewriting the formula, as in (2), it is possible to get a measure of
performance expressed in effective number of bits (N). The
effective number of bits for a device can be calculated directly
from its measured SNR.
N
=
SNR
–1.76
6.02
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7878LP | IC LOGIC 125 LOW-VOLTAGE SINGLE FET 8-OHM BUS SWITCH -40+85C SC-70-5 3000/REEL |
| AD7878JN | LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878JP | LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7880 | Enclosed Switches Series LS: Rod - Adjustable; 1NC 1NO DPDT Snap Action, Double Break; 0.5 in - 14NPT conduit; Plug-in |
| AD7880CR | LC2MOS Single +5 V Supply, Low Power, 12-Bit Sampling ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7878LP | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin PLCC 制造商:Rochester Electronics LLC 功能描述:12-BIT ADC IC - Bulk |
| AD7878LPZ | 功能描述:IC ADC 12BIT W/DSP INT 28-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD7878LPZ-REEL | 功能描述:IC ADC 12BIT W/DSP 28PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7878SE | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878SE/883B | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12-BIT ADC IC - Bulk 制造商:Analog Devices 功能描述:CONVERTER - ADC |
發布緊急采購，3分鐘左右您將得到回復。